Ericsson AVP 4000 Reference Manual Download Page 237

Page: 237 / 422

Web GUI Control

1/1553-FGC 101 1790

Uen

5-53

Parameter

Values

Description

AS Index Control

Don't Care, Use 1, Use 1 + 2

Only available when Splicing Control is set to On VANC

Message Only.
If set to Don’t Care the AVP 4000 will create SCTE 35

output regardless of the source Automation System.
If set to Use 1 the AVP 4000 will create SCTE 35 output

only for incoming SCTE 104 whose AS Index matches the

setting in AS Index 1.
If set to Use 1 + 2 the AVP 4000 will create SCTE 35

output only for incoming SCTE 104 messages whose AS

Index matches either the setting in AS Index 1 or the

setting in AS Index 2.

DPI PID Index Control

Don't Care, Use 1, Use 1 + 2

Determines how many values of DPI PID Index are

compared against the incoming SCTE 104 message.

Available only when Splicing Control is set to On VANC

Message Only.

AS Index 1

0 to 255

The AS index used if AS Index Control is set to Use 1 or

Use 1 + 2.

AS Index 2

0 to 255

The AS index used if AS Index Control is set to Use 1 + 2.

DPI PID Index 1

0 to 255

The DPI PID index used if DPI PID Index Control is set to

Use 1 or Use 1 + 2.

DPI PID Index 2

0 to 255

The DPI PID index used if DPI PID Index Control is set to

Use 1 + 2.

SCTE 104 Encode

Input Stream Channel

None

Only available if triggering splicing based on contact

closure through a GPI card.

Splicing Component

The following parameters are available on the

Component

tab of the

Properties

widget on the

Service Configuration

page when an SCTE 35 stream is selected in

the

Outputs

widget. The same parameters can be accessed through the

Output/<output name>/Transport Stream ID: <n>/Service List/<service

name>/Component List/<component name>

menu on the front panel.

Table 5.28 Slicing Component Parameters

Parameter

Values

Description

PID

32 to 8190

Sets the packet identifier associated with the component.

Bit Rate Weighting

Fixed

Specifies the weight associated to the component in the

Bit Rate Tracking algorithm. For audio stream, this is Fixed

and read only.

5.5.3.1.4

Teletext Stream Configuration

This section describes the parameters for setting up Teletext.

Teletext

This section gives the parameters that have an effect on how Teletext is transmitted.

Summary of Contents for AVP 4000







































































































































































































































































































































































































































Search results

Summary of Contents for AVP 4000

Reviews:

Ericsson AVP 4000, Reference Manual, Page: 237 / 422

Search results

Summary of Contents for AVP 4000

Reviews: