manualshive.com logo in svg

Ericsson AVP 4000, Reference Manual, Page: 41 / 422

Share
Download
Ericsson AVP 4000 Reference Manual Download Page 41

 

Getting Started 

 

 

1/1553-FGC 101 1790 Uen Y 

 

3-5 

 

 

 

Figure 3.79

 

Fan Control ..................................................................................... 3-99

 

Figure 3.80

 

Video License Error Message ....................................................... 3-100

 

Figure 3.81

 

Finding the Host Card Chip ID for License Generation. ................. 3-101

 

Figure 3.82

 

Alarm Monitoring ........................................................................... 3-102

 

 

List of Tables 

Table 3.1

 

IP Address Restrictions ..................................................................... 3-9

 

Table 3.2

 

Ethernet Control Port Parameters ................................................... 3-10

 

Table 3.3

 

Ethernet Data Port Parameters ....................................................... 3-12

 

Table 3.4

 

Installation of Option Cards ............................................................. 3-21

 

Table 3.5

 

Configuration of Option Cards ......................................................... 3-22

 

Table 3.6

 

Repositioning Options ..................................................................... 3-44

 

Table 3.7

 

VLAN Creation Options ................................................................... 3-53

 

Table 3.8

 

VLAN Tag Sharing Options .............................................................. 3-53

 

Table 3.9

 

SD or PiP Output with Combination of Aspect Ratio Settings .......... 3-59

 

Table 3.10

 

Audio Pass-thru Bit Rate Configuration ........................................... 3-71

 

Table 3.11

 

Embedded Stereo Channel Pairs .................................................... 3-71

 

Table 3.12

 

License Requirements for PAA Encoding ........................................ 3-74

 

Table 3.13

 

VANC Filtering Wild-cards ............................................................... 3-79

 

Table 3.14

 

Video Parameter Settings................................................................ 3-80

 

Table 3.15

 

Audio Input Settings ........................................................................ 3-81

 

Table 3.16

 

Audio Encode Settings .................................................................... 3-81

 

Table 3.17

 

Transport Stream Parameters ......................................................... 3-82

 

Table 3.18

 

IP Related Parameters .................................................................... 3-83

 

Table 3.19

 

Component and Service Parameters ............................................... 3-83

 

Table 3.20

 

AVP 4000 Video Input and Pre-Processing Parameters .................. 3-84

 

Table 3.21

 

AVP 4000 Video Encoder Parameters ............................................. 3-85

 

Table 3.22

 

AVP 4000 Seamless and Reflex Operation ..................................... 3-86

 

Table 3.23

 

GOP Length .................................................................................... 3-87

 

Table 3.24

 

Input Options Parameters ............................................................... 3-89

 

Table 3.25

 

Encode Options Parameters ........................................................... 3-89

 

Table 3.26

 

Example Multiple Operation SCTE104 Message Structure .............. 3-96

 

Table 3.27

 

DPI PID Index Value ........................................................................ 3-96

 

Table 3.28

 

Splicing Control Options .................................................................. 3-97

 

Table 3.29

 

SNMP Interface Parameters .......................................................... 3-103

 

 

 

Summary of Contents for AVP 4000







































































































































































































































































































































































































































Reviews:

No comments