Ericsson AVP 4000 Reference Manual Download Page 219

Page: 219 / 422

Web GUI Control

1/1553-FGC 101 1790

Uen

5-35

Parameter

Values

Description

Freeze Frame and Silence

Detect

Time Threshold

Before Slate

Time Threshold Before Slate

Time Threshold

Before Recovery

Time Threshold Before Recovery

Silent Audio

Detect

Time Threshold

Before Slate

Time Threshold Before Slate

Time Threshold

Before Recovery

Time Threshold Before Recovery

Audio Threshold

-100 dBFS to - -40 dBFS

The selected audio component will be deemed silent if all

of its channel have a volume level below this threshold.

Audio Selection

Audio Stream 1 to 16

Audio component on which to perform silence detection

(applicable to “Freeze Frame and Silence” and “Silent

Audio” detection), if possible: silence detection is not

available for pass-through components.

Only available for E9001T licensed with AVP/SWO/TRANS.

Vertical Blanking Interval / Ancillary Data

The following parameters are available on the

VBI

tab of the

Properties

widget on

the

Service Configuration

page when a video stream is selected in the

Outputs

widget. The same parameters can be accessed through the

Advanced/EI9001/Video/Video 1/Input/VBI Extraction

menu on the front panel.

Table 5.6 Vertical Blanking Interval / Ancillary Data Parameters

Parameter

Values

Description

Timecode

TC Mode

Off, External, Zero on Loss, External, Freewheel

on Loss, Internal

Controls what mode the Time code (TC) is working in,

either Off, external source or internally generated. Also

sets what happens on loss of external source (zero or

freewheel).

TC External Source

Auto, ANC VITC1, ANC VITC2, ANC LTC, VBI

VITC

Controls the external source of Time Code. Auto will select

the first source present in order of the drop down list.

VBI Line Control

Manual, RX8

Selects if the VBI line control is set by the user, or

determined automatically by the RX8 decoder (EI9001T

card only).

TC Dropframes

Off, On, Auto

Only in 525 line operation controls if Time Code takes

account of drop frames or not. Auto configures to external

source, or to ON for internal source.

Field 1

VBI Line 9 - VBI Line

Off, VITC, Closed Captions, Monochrome

Samples

Specifies the content in the respective VBI lines. Set to Off

if the line in the incoming video does not carry any

information, Closed Caption for closed caption information.

Visible for 480i (525-line) input streams.

Summary of Contents for AVP 4000







































































































































































































































































































































































































































Search results

Summary of Contents for AVP 4000

Reviews:

Ericsson AVP 4000, Reference Manual, Page: 219 / 422

Search results

Summary of Contents for AVP 4000

Reviews: