Ericsson AVP 4000 Reference Manual Download Page 405

Page: 405 / 422

Alarm Lists

1/1553-FGC 101 1790 Uen X

D-15

Alarm

Description

Port Number

Alarm ID

Source

Severity

Audio 5 VPS/ARIB Coding Mode

Mismatch

The coding mode signalled by

VPS/ARIB is not supported by the

current Audio Codec

0312208B

Audio 5

minor

Audio 6 Input lock

No valid audio detected on selected

input. Please check source

connection.

031220A0

Audio 6

major

Audio 6 TS input error

Incoming transport stream error.

Please check source TS.

031220A1

Audio 6

major

Audio 6 Compressed audio not

detected

Compressed audio not detected on

input. Please check source

connection and source format.

031220A2

Audio 6

minor

Audio 6 Input frame CRC failure

CRC error in compressed input

frame. Output is muted.

031220A3

Audio 6

minor

Audio 6 Unsupported sample

rate

Unsupported sample rate at decoder

output.

031220A4

Audio 6

minor

Audio 6 Dolby E program not

present

Program not present in Dolby E

stream.

031220A5

Audio 6

minor

Audio 6 Dolby E alignment

Dolby E frames not properly aligned

to video frames. May glitch on frame

drop/repeat and video may not be

aligned to audio.

031220A6

Audio 6

minor

Audio 6 Dolby E metadata frame

rate mismatch

Frame rate indicated in Dolby E

metadata does not match current

video frame rate.

031220A7

Audio 6

minor

Audio 6 ADS control track

Control track for audio description

not present.

031220A8

Audio 6

minor

Audio 6 ADS silence

Silent period detected. Valid only for

Audio Description Service encoding.

031220A9

Audio 6

minor

Audio 6 Clipping

Audio output is clipping. Audio gain

value or input amplitude should be

reduced.

031220AA

Audio 6

minor

Audio 6 VPS/ARIB Coding Mode

Mismatch

The coding mode signalled by

VPS/ARIB is not supported by the

current Audio Codec

031220AB

Audio 6

minor

Audio 7 Input lock

No valid audio detected on selected

input. Please check source

connection.

031220C0

Audio 7

major

Audio 7 TS input error

Incoming transport stream error.

Please check source TS.

031220C1

Audio 7

major

Audio 7 Compressed audio not

detected

Compressed audio not detected on

input. Please check source

connection and source format.

031220C2

Audio 7

minor

Audio 7 Input frame CRC failure

CRC error in compressed input

frame. Output is muted.

031220C3

Audio 7

minor

Audio 7 Unsupported sample

rate

Unsupported sample rate at decoder

output.

031220C4

Audio 7

minor

Audio 7 Dolby E program not

present

Program not present in Dolby E

stream.

031220C5

Audio 7

minor

Summary of Contents for AVP 4000







































































































































































































































































































































































































































Search results

Summary of Contents for AVP 4000

Reviews:

Ericsson AVP 4000, Reference Manual, Page: 405 / 422

Search results

Summary of Contents for AVP 4000

Reviews: