manualshive.com logo in svg

Commodore Amiga A1000, Hardware Reference Manual

Share
Download
Commodore Amiga A1000 Hardware Reference Manual Download Page 365

DKWEB- (Pin #16)

 

    This signal causes a selected drive to start writing data (provided

 

by DKWDB-) onto the disk.

 

 

CHNG- (Pin #11)

 

    A selected drive will drive this signal low whenever its internal

 

"disk change" latch is set.

 

This latch is set when the drive is first powered on, or whenever there

 

is no diskette in the drive. To reset the latch, the system must select

 

the drive, and step the head. Of course, the latch will not reset if

 

there is no diskette installed.

 

 

MTRXD- (Pin #8)

 

    This is the motor control line for all four disk drives. When the

 

system wants to turn on a disk drive motor, it first deselects the drive

 

(if selected), pulls MTRXD- low, and selects the drive. To turn the motor

 

off, the system deselects the drive, pulls MTRXD- high, and selects the

 

drive. The system will always set MTRXD- at least 1.4 microseconds before

 

it selects the drive, and will not change MTRXD- for at least 1.4

 

microseconds after selecting the drive. An external drives must have

 

logic equivalent to a D flip-flop, whose D input is the MTRXD signal, and

 

whose clock input is activated by the off-to-on (high-to-low) transition

 

of its SELxB- signal. As noted above, both the setup and hold times of

 

MTRXD-with respect to SELxB- will always be at least 1.4 microseconds.

 

The output of this flip-flop controls the disk drive motor. Thus, the

 

system can control all four motors using only one signal on the cable

 

(MIRXD-).

 

 

DRESB- (Pin #10)

 

    This signal is a buffered version of the system reset signal. Three

 

things can make it go active low):

 

 

o  System power-up (DRESB- will go low for approximately one second);

 

 

o  System CPU executes a RESET instruction (DRESB- will go low for

 

approximately 17 microseconds);

 

 

o  Hard reset from keyboard (lasts as long as keyboard reset is held

 

down).

 

 

External disk drives should respond to DRESB- by shuffling off their motor

 

flip-flops and write protecting themselves.

 

 

A level of 3.75v or below on the 5v+ requires external disks to write-

 

protect and reset the motor on line.

 

 

                            
 
 
 
 
 
 
 
 
 
 
 
 
 

- 356 Appendix I -

 

Summary of Contents for Amiga A1000





























































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands