manualshive.com logo in svg

Commodore Amiga A1000, Hardware Reference Manual

Share
Download
Commodore Amiga A1000 Hardware Reference Manual Download Page 282

DSKDAT      026    W    P   Disk DMA data write

 

DSKDATR     008    ER   P   Disk DMA data read (early read dummy

 

                                  address )

 

 

                 This register is the disk DMA data buffer. It

 

                 contains two bytes of data that are either sent

 

                 (written) to or received (read) from the disk.

 

                 The write mode is enabled by bit 14 of the LENGTH

 

                 register. The DMA controller automatically

 

                 transfer data to or from this register and RAM,

 

                 and when the DMA data is finished (length=0) it

 

                 causes a disk block interrupt. See interrupts below.

 

 

DSKLEN      024    W    P   Disk length

 

 

                 This register contains the length (number of words)

 

                 of disk DMA data. It also contains two control

 

                 bits, a DMA enable bit, and a DMA

 

                 direction (read/write) bit.

 

 

                 BIT#   FUNCTION       DESRIPTION

 

                 -------------------------------------------------

 

                 15     DMAEN          Disk DMA enable

 

                 14     WRITE          Disk write (RAM to disk) if 1

 

                 13-0   LENGTH         Length (# of words) of DMA data.

 

 

DSKPTH      020    W    A   Disk pointer (high 3 bits)

 

DSKPTL      022    W    A   Disk pointer (low 15 bits)

 

 

                 This pair of registers contains the 18-bit

 

                 address of disk DMA data. These address registers

 

                 must be initialized by the processor or Copper

 

                 before disk DMA is enabled.

 

 

DSKSYNC     07E    W    P   Disk sync register

 

 

                 hold the match code for disk read synchronization.

 

                 See ADKCON bit 10.

 

 

                            
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

- Appendix A 273 -

 

Summary of Contents for Amiga A1000





























































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands