manualshive.com logo in svg

Commodore Amiga A1000, Hardware Reference Manual

Share
Download
Commodore Amiga A1000 Hardware Reference Manual Download Page 314

SERIAL INTERFACE CONNECTOR ELECTRICAL CHARACTERISTICS

 

 

OUTPUTS MIN  TYP MAX

 

------- ---  --- ---

 

Vo(-):  13.2 -x- -2.5   V      Negative output voltage range

 

Vo(+):  8.0  -x-  13.2  V      Positive output voltage range

 

Io:     -x-  -x-  10.0  ma     Output current

 

 

INPUTS MIN  TYP MAX

 

------ ---  --- ---

 

Vi(+): 3.0  -x- 25.0   V       Positive input voltage range

 

Vi(-): 25.0 -x- 0.5    V       Negative input voltage range

 

Vhy:   -x-  1.0 -x-    V       Input hysteresis voltage

 

Ii:    0.3  -x- 10.0   ma      Input current

 

 

Unconnected inputs are interpreted the same as positive input voltages.

 

 

GAME CONTROLLER INTERFACE CONNECTOR SPECIFICATION

 

 

The two 9-pin D-type connectors with pins (male) are used to

 

interface to four types of devices:

 

 

1. Mouse or trackball, 3 buttons max.

 

 

2. Digital joystick, 2 button max.

 

 

3. Proportional (pot or proportional joystick), 2 buttons max.

 

 

4. Light pen, including pen-pressed-to-screen button.

 

 

The connector pin alignment are discussed in sections organized

 

by similar hardware and/or software operating requirements as shown

 

in the previous list. Signal names follow those used elsewhere

 

in this appendix, when possible.

 

 

J11 is the right controller port connector (JOY1DAT, POT1DAT).

 

J12 is the left controller port connector (JOY0DAT, POT0DAT).

 

 

NOTE: While most of the hardware discussed below is directly

 

accessible, hardware should be accessed through ROM kernel software.

 

This will keep future hardware changes transparent to the user.

 

 

                            
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

- Appendix E 305 -

 

Summary of Contents for Amiga A1000





























































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands