manualshive.com logo in svg

Commodore Amiga A1000, Hardware Reference Manual

Share
Download
Commodore Amiga A1000 Hardware Reference Manual Download Page 200

The 68000 uses only the even-numbered memory access cycles. The 68000 spends about 
half of a complete processor instruction time doing internal operations and the other half 

accessing  memory.  Therefore,  the  allocation  of  alternate  memory  cycles  to  the  68000 
makes it appear to the 68000 that it has the memory all of the time, and it will run at full 
speed. 

 
Some  68000  instructions  do  not  match  perfectly  with  the  allocation  of  even  cycles  and 

cause  cycles  to  be  missed.  If  cycles  are  missed,  the  68000  must  wait  until  its  next 
available memory slot before continuing. However, most instructions do not cause cycles 
to be missed, so the 68000 runs at full speed most of the time if there is no blitter DMA 

interference. 
 
Figure 6-10 illustrates the normal cycle of the 68000. 

 
NOTE 
The  68000  test-and-set  instruction  (TAS)  should  never  be  used  in  the  Amiga;  the 

indivisible  read-modify-write  cycle  that  is  used  only  in  this  instruction  will  not  fit  into  a 
DMA memory access slot. 

 

     -------------------------------------------------------------

 

     |              <---- Average 68000 cycle ---->              |

 

     |                                                           |

 

     |     <--- internal --->       |     <--- memory --->       |

 

     |         operation            |          access            |

 

     |          portion             |         portion            |

 

     |                              |                            |

 

     |         odd cycle,           |        even cycle          |

 

     |        assigned to           |       available to         |

 

     |       other devices          |        the 68000           |

 

     -------------------------------------------------------------

 

 

                     Figure 6-10: Normal 68000 Cycle

 

 
 

If the display contains four or fewer low-resolution bit-planes, the 68000 can be granted 

alternate memory cycles (if it is ready to ask for the cycle and is the highest priority item 
at the time). However, if there are more than four bit-planes, bit-plane DMA will begin to 
steal cycles from the 68000 during the display. 

 
During  the  display  time  for  a  six-bit-plane  display  (low  resolution, 320  pixels  wide),  160 
time  slots  will  be  taken  by  bit-plane  DMA  for  each  horizontal  line.  As  you  can  see  from 

Figure 6-11,  bit-plane  DMA  steals 50  percent  of the  open  slots that  the  processor might 
have used if there were only four bit-planes displayed. 

 

                        

 

 
 
 
 
 
 
 
 
 
 
 
 
 

- Blitter Hardware 191 -

 

Summary of Contents for Amiga A1000





























































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands