manualshive.com logo in svg

Commodore Amiga A1000, Hardware Reference Manual

Share
Download
Commodore Amiga A1000 Hardware Reference Manual Download Page 333

SERIAL SHIFT REGISTER (SDR)

 

 

The serial port is a buffered, 8-bit synchronous shift register. A

 

control bit selects input or output mode. In the Amiga system one shift

 

register is used for the keyboard, and the other is unassigned. Note that

 

the RS-232 compatible serial port is controlled by the Paula chip; see

 

chapter 8 for details.

 

 

INPUT MODE

 

In input mode, data on the SP pin is shifted into the shift register on

 

the rising edge of the signal applied to the CNT pin. After eight CNT

 

pulses, the data in the shift register is dumped into the serial data

 

register and an interrupt is generated.

 

 

OUTPUT MODE

 

In the output mode, Timer A is used as the baud rate generator. Data is

 

shifted out on the SP pin at 1/2 the underflow rate of Timer A. The

 

maximum baud rate possible is 02 divided by 4, but the maximum usable

 

baud rate will be determined by line loading and the speed at which the

 

receiver responds to input data.

 

 

To begin transmission, you must first set up Timer A in continuous mode,

 

and start the timer. Transmission will start following a write to the

 

serial data register. The clock signal derived from Timer A appears as an

 

output on the CNT pin. The data in the serial data register will be

 

loaded into the shift register, then shifted out to the SP pin when a CNT

 

pulse occurs. Data shifted out becomes valid on the next falling edge of

 

CNT and remains valid until the next falling edge.

 

 

After eight CNT pulses, an interrupt is generated to indicate that more

 

data can be sent. If the serial data register was reloaded with new

 

information prior to this interrupt, the new data will automatically be

 

loaded into the shift register and transmission will continue.

 

 

If no further data is to be transmitted after the eighth CNT pulse, CNT

 

will return high and SP will remain at the level of the last data bit

 

transmitted.

 

 

SDR data is shifted out MSB first. Serial input data should appear in

 

this same format.

 

 

                            
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

- 324 Appendix F -

 

Summary of Contents for Amiga A1000





























































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands