manualshive.com logo in svg

Agilent Technologies J-BERT N4903B, User Manual, Page: 236 / 572

Share
Download
Agilent Technologies J-BERT N4903B User Manual Download Page 236

At 100MHz, the pulse period is 1/100 × 10

-6

s = 10

-8

s = 10ns; this is the unit interval

(UI). For example, a value - in fact, any parameter that is specified in time units -

of 37ns is equivalent to 37ns/10ns=3.7UI (time values are expressed as multiples

of the unit interval).

This makes it easy to analyze measurements at different frequencies: If the

measured phase margin is 8ns at 100MHz (1UI=10ns), and 4ns at 200MHz

(1UI=5ns): The phase margin is 0.8UI in both cases, and it is immediately obvious

that it does not depend on the system frequency.
The same is true for the delay resolution parameter in the DUT Output Timing/

Jitter and Eye Opening measurements: If you specify the delay resolution as 0.01UI,

the measurement software will always measure 150 points across the bathtub, no

matter what system frequency you choose (only if edge optimization is switched

off, of course). However, if you specify the resolution in time, the number of

measured points will change inversely proportional to the system frequency

(doubling the frequency results in half the number of measured points).

Syntax Requirements

All time-related entries understand both time and unit interval notation, regardless

of the UI/time selection made in the 

View

 tab of the 

Properties

 dialog box. You

can enter 17s, 5ns or 0.01UI at any time. On run, the Serial BERT will automatically

convert all entries to time values, using the current unit interval. So, the UI is handy

if you want to set values independently from the system frequency.
All voltage-related entries understand 23mV, 0.01V, and so on.
All power-related values can be entered as 50mW, 0.04W, 6dBm,and so on.
All dimensionless quantities understand decimal notations (e.g. 10000000, 0.0003)

and scientific/engineering notation (e.g. 1e9, 1.7e-3).

Marker Definitions

Markers are available for all measurements except of the Fast Eye Mask. They

make the analysis and tracing of the results more comfortable. Markers can be

switched on or off at any time when results are available in the graphical view. For

the DUT Output Timing/Jitter measurement, the software provides two types of

markers.

The following illustration shows the definitions for the markers and the values that

can be derived from the marker position.

6

Advanced Analysis

236

Agilent J-BERT N4903B High-Performance Serial BERT

Example

Measurements at different frequencies

Linear Markers

Summary of Contents for J-BERT N4903B





























































































































































































































































































































































































































































































































































































Reviews:

No comments