Rigaku MiniFlex 600 Скачать руководство пользователя страница 98

Страница: 98 / 111

Maintenance

MiniFlex 600: Benchtop X-ray Diffractometer

remaining in the hose can be prevented from leaking out by keeping the end
of the removed cooling water hose at a high position.

Remove the upper cover

①

of the enclosure. (Tool used: Philips

screwdriver)

Fig. 9.1 Separating upper cover and separating X-ray tube

Loosen the two screws

②

of X-ray tube. (Tool used: Slotted

screwdriver)

Remove the X-ray tube

③

CAUTION

Make sure that the water remaining inside the X-ray tube does not drip inside
the tube shield. If the water drips into the X-ray tube shield, thoroughly dry the
interior by absorbing the water with a piece of cloth or soft paper.

Fig. 9.2 Inside the enclosure (rear view with the upper cover removed)

Sample

chamber

door

X-ray tube

Sample

position

Tube shield

Tube fixing screws

Standard sample

holder

Counter (SC)

Cooling water tube

connection port

①

Содержание MiniFlex 600
















































































































Результаты поиска

Содержание MiniFlex 600

Отзывы:

Похожие инструкции для MiniFlex 600

Бренды по названию

Популярные бренды

Rigaku MiniFlex 600, Инструкция по эксплуатации

Результаты поиска

Содержание MiniFlex 600

Отзывы:

Похожие инструкции для MiniFlex 600

Бренды по названию

Популярные бренды