Rigaku MiniFlex 600 Скачать руководство пользователя страница 51

Страница: 51 / 111

Optics Alignment (Required for Periodic Inspection or Installing X-Ray Tube)

MiniFlex 600: Benchtop X-ray Diffractometer

Execute the D/teX Detector Center Correction. - with sample

①

Select

Tasks

Package Measurement

Maintenance

D/teX

Detector Adjustment - D/teX Detector Center Correction

②

Check the

Center Correction Clear

checkbox.

③

Click the

Execute

button.

④

Uncheck the

Center Correction Clear

checkbox.

⑤

Install the beam stop. If the retracting screw is mounted on the

variable knife edge, remove it. Fill the 0.5-mm deep glass sample
plate with angle reference material (NIST, SRM-640d) and set it on
the sample holder.

⑥

Check the

Theta/2-theta scan conditions

checkbox.

⑦

Set DS=1.25° and SS=RS=OPEN.

When the incident and receiving Soller slits are 5°, enter 47.25° in the

Theta/2-theta position (deg)

box. When the incident and receiving

Soller slits are 2.5°, enter 47.26° in the

Theta/2-theta position (deg)

box.

⑧

Click the

Execute

button.

The correction value is registered in the MiniFlex Guidance
automatically after the measurement is completed.

⑨

Click the

button.

Fig. 6.2.21 D/teX Detector Center Correction window

Содержание MiniFlex 600
















































































































Результаты поиска

Содержание MiniFlex 600

Отзывы:

Похожие инструкции для MiniFlex 600

Бренды по названию

Популярные бренды

Rigaku MiniFlex 600, Инструкция по эксплуатации

Результаты поиска

Содержание MiniFlex 600

Отзывы:

Похожие инструкции для MiniFlex 600

Бренды по названию

Популярные бренды