Rigaku MiniFlex 600 Скачать руководство пользователя страница 33

Страница: 33 / 111

Installing the DS and IHS (Length limiting)

MiniFlex 600: Benchtop X-ray Diffractometer

Installing the DS and IHS (Length limiting)

Install the DS=1.25° to the DS section.

Insert the IHS layered with DS of X-ray tube side.

The IHS is a slit to limit the longitude direction of a slit.
During a variable slit mode, insert only the IHS.

Fig. 5.23 Enlarged image of DS

Connecting the power cable

Connect the power cable to the power cable connector on the rear side

of MiniFlex 600 main unit.

For power supply input cable with plug (single phase 100 V – 240 V AC

power supply), connect the power supply input cable to a dedicated power
supply of 15 A grounded power outlet (3-contact). The standard included
power cable is compatible up to 125 V AC.

Connecting with Computer

Connect the LAN connection port of the computer to the LAN

connection port on the rear side of MiniFlex 600 main unit (inner side)
with the LAN cable.

If there are more than two LAN connection ports on the PC side, connect to
the specified LAN connection port.

Position to insert DS and IHS

Содержание MiniFlex 600
















































































































Результаты поиска

Содержание MiniFlex 600

Отзывы:

Похожие инструкции для MiniFlex 600

Бренды по названию

Популярные бренды

Rigaku MiniFlex 600, Инструкция по эксплуатации

Результаты поиска

Содержание MiniFlex 600

Отзывы:

Похожие инструкции для MiniFlex 600

Бренды по названию

Популярные бренды