Rigaku MiniFlex 600 Скачать руководство пользователя страница 66

Страница: 66 / 111

Setting and Adjustment

MiniFlex 600: Benchtop X-ray Diffractometer

⑥

Click the

Execute

button.

The correction value is registered in the MiniFlex Guidance
automatically after the measurement is completed.

⑦

Click the

button.

Fig. 6.2.41 Measurement condition

Confirm that the direct beam is blocked.

①

Mount the Cu absorber (0.3 mm x 1) on the Soller slit box. If the
beam stop is not mounted, mount it.

②

xecute measurement of direct beam and confirm that the direct beam

is blocked by the beam stop.

Scan conditions, Absolute, Start: -0.4, Stop: 0.4, Step: 0.01, Speed: 5, Scan
mode: Continuous
Count mode under Detector: Int.

・

If part of or the whole direct beam can be seen, perform the procedures

Adjust the beam stop

・

When it is confirmed that the direct beam is blocked by the beam stop,

go on to

Perform the beam stop position confirmation

measurement.

Enter 0° when using the

direct beam

Содержание MiniFlex 600
















































































































Результаты поиска

Содержание MiniFlex 600

Отзывы:

Похожие инструкции для MiniFlex 600

Бренды по названию

Популярные бренды

Rigaku MiniFlex 600, Инструкция по эксплуатации

Результаты поиска

Содержание MiniFlex 600

Отзывы:

Похожие инструкции для MiniFlex 600

Бренды по названию

Популярные бренды