Rigaku MiniFlex 600 Скачать руководство пользователя страница 91

Страница: 91 / 111

Measurement with MiniFlex Guidance

MiniFlex 600: Benchtop X-ray Diffractometer

Measurement with MiniFlex Guidance

Once the sample plate filled with the sample has been placed on the sample
holder, measurement can be conducted by

Package Measurement

–

General

Measurement

of MiniFlex Guidance. The measurement conditions for

qualitative analysis patterns are given below. For details on the procedures, refer
to the Help menu of MiniFlex Guidance.

Select Package Measurement – General Measurement.

In this window, specify the names of the folder and file where you want to
save measurement data and the name of the sample. The number in the

Condition

box corresponds to the number of the measurement condition

set to be used. Measurement conditions can be entered by clicking on the

Condition Setting

button. It is convenient to assign a number to a set of

typical measurement conditions and specify that number for a routine
measurement.

Fig. 8.6 General Measurement

Enter File name etc.

Measurement start button

Measurement Conditions

button

Содержание MiniFlex 600
















































































































Результаты поиска

Содержание MiniFlex 600

Отзывы:

Похожие инструкции для MiniFlex 600

Бренды по названию

Популярные бренды

Rigaku MiniFlex 600, Инструкция по эксплуатации

Результаты поиска

Содержание MiniFlex 600

Отзывы:

Похожие инструкции для MiniFlex 600

Бренды по названию

Популярные бренды