Rigaku MiniFlex 600 Скачать руководство пользователя страница 23

Страница: 23 / 111

MiniFlex 600: Benchtop X-ray Diffractometer

Installation of MiniFlex600

Unpacking

Unpack the main unit and the component parts, and verify that they match with
the list of shipped items (see “

List of Shipped Items

”).

Installing the X-Ray tube

Remove the upper cover of the enclosure.

①

Remove the six fixing screws on (3 x 2) on both sides of the main
unit.

②

Pull the cover slightly backward, and then lift it up.

Fig. 5.1 Removing the upper cover of the enclosure

Install the X-ray tube.

①

Remove the upper cover. The X-ray tube is on the left side when
looking at the equipment from the front side.

②

Place the O-rings (two, included within the storage box) on the upper
side of the tube shield.

Without the O-rings, the cooling water may leak out.

Upper side of the

enclosure

Direction to remove

cover

Screws

fastening the

upper cover

(Total of six

screws on left

and right)

Содержание MiniFlex 600
















































































































Результаты поиска

Содержание MiniFlex 600

Отзывы:

Похожие инструкции для MiniFlex 600

Бренды по названию

Популярные бренды

Rigaku MiniFlex 600, Инструкция по эксплуатации

Результаты поиска

Содержание MiniFlex 600

Отзывы:

Похожие инструкции для MiniFlex 600

Бренды по названию

Популярные бренды