Rigaku MiniFlex 600 Скачать руководство пользователя страница 57

Страница: 57 / 111

Optics Alignment (Required for Periodic Inspection or Installing X-Ray Tube)

MiniFlex 600: Benchtop X-ray Diffractometer

③

If a variable knife edge is installed, either remove it or mount the
retracting screw and keep the slider of the variable knife edge lifted
up.

Fig. 6.2.29 Absorbers and its position to install

CAUTION

The absorber is inserted in order to prevent the direct beam from being directly
entering the detector. The detector may be damaged if the absorber is not
installed. Be sure to install the absorber upon an optics alignment.

Set the environmental settings of goniometer and detector for optics

alignment.

①

Start up MiniFlex Guidance and select

Options

–

Hardware

Configuration

②

Confirm that the

Standard Sample Holder

and

D/teX Ultra

are

selected as the

Attachment

and

Detector

respectively.

③

Click

Goniometer

, and set the

User setting

Min.

−

3°.

Update

the hardware configuration after the setting is completed.

④

Update the hardware configuration after the setting is completed.

Fig. 6.2.30 Hardware Configuration window

Absorber

Remove the

beam stop

Содержание MiniFlex 600
















































































































Результаты поиска

Содержание MiniFlex 600

Отзывы:

Похожие инструкции для MiniFlex 600

Бренды по названию

Популярные бренды

Rigaku MiniFlex 600, Инструкция по эксплуатации

Результаты поиска

Содержание MiniFlex 600

Отзывы:

Похожие инструкции для MiniFlex 600

Бренды по названию

Популярные бренды