Rigaku MiniFlex 600 Скачать руководство пользователя страница 54

Страница: 54 / 111

Setting and Adjustment

MiniFlex 600: Benchtop X-ray Diffractometer

Fig. 6.2.24 Adjusting the beam stop

Perform the beam stop position confirmation measurement.

CAUTION

Before performing the beam stop position confirmation measurement, make
sure that the direct beam is blocked by the beam stop in

Perform direct

beam confirmation measurement.

The detector may become damaged if the

direct beam enters D/teX Ultra directly.

①

Remove the Cu absorber mounted on Soller slit box.

②

Set the setting jig (with Si) on the sample holder. .

③

Confirm that the beam stop is not set at a position where it interferes

with the measurement. Perform the beam stop position confirmation
measurement.

④

Confirm that the background intensity at 2θ=2° or larger is not

blocked by the beam stop.

⑤

If an adjustment is required again, return to

Adjust the beam stop

and perform the adjustment.

Scan conditions, Absolute, Start: 1, Stop: 5, Step: 0.01, Speed: 10, Scan
mode: Continuous
Count mode under Detector: Diff.

Beam stop

fixing screw

Beam stop

mounting

screw

Adjusting

screw

Содержание MiniFlex 600
















































































































Результаты поиска

Содержание MiniFlex 600

Отзывы:

Похожие инструкции для MiniFlex 600

Бренды по названию

Популярные бренды

Rigaku MiniFlex 600, Инструкция по эксплуатации

Результаты поиска

Содержание MiniFlex 600

Отзывы:

Похожие инструкции для MiniFlex 600

Бренды по названию

Популярные бренды