Cmsemicon BAT32G1 9 Series Скачать руководство пользователя | Manualshive

Страница: 517 / 1149

background image

BAT32G1x9 user manual | Chapter 15 A/D converter

517 / 1149

Rev.1.02

15.4.10 Hardware-triggered wait mode (select mode, single-shot transition mode)

①

In the stopped state, enter the hardware-triggered standby state by placing the ADCE position "1" of

the ADM0's mode register 0 (ADM0).

②

If the input hardware trigger is in hardware-triggered standby, A/D conversion is performed on the

analog input specified by the analog input channel specified by the register (ADS). The ADCS
position of the ADM0 register is automatically "1" while the input hardware is triggered.

③

If the A/D conversion is complete, the conversion result is saved to the A/D conversion result

register (ADCR, ADCRH) and an A/D transition end interrupt request signal is generated (INTAD)

。

④

After the A/D conversion is complete, the ADCS bit is automatically cleared to "0" and the A/D

converter enters the stopped state.

⑤

If the input hardware is triggered during the conversion, the current A/D conversion is aborted

immediately and the conversion is restarted.

⑥

If the ADS registers are overwritten or rewritten during the conversion process, the current A/D

conversion is immediately aborted and the analog inputs reassigned by the ADS registers are A/D
converted.

⑦

If you rewrite "1" for the ADCS bit during the conversion process, the current A/D conversion is

immediately aborted and the conversion restarts.

⑧

If the ADCS position is "0" during the conversion, the current A/D conversion is aborted immediately,

then the hardware triggers the standby state, and the A/D converter enters the stopped state. When
the ADCE bit is "0", even the input hardware trigger is ignored and the A/D conversion does not
begin.

Figure15-29 Operation sequence of hardware trigger wait mode (select mode, single-shot transition mode).

p

o

w

e

r

so

u

rce

p

o

w

e

r

so

u

rce

p

o

w

e

r

so

u

rce

p

o

w

e

r

so

u

rce

p

o

w

e

r

so

u

rce

A/D conversion state

stop

converting

idle
conversion

set 1 to ADCE bit

generate hardware trigger

hardware trigger

do not accept trigger

trigger idle

clear ADCE bit to 0

do not accept trigger

modify ADS (from ANI0 to

ANI1) during A/D conversion

clear ADCS bit to 0
during conversion

rewrite ADCS bit to 1

during A/D conversion
operation

trigger idle

generate hardware trigger
during A/D conversion
operation

auto restart
conversion when
conversion
completes

conversion completes

auto restart
conversion when
conversion
completes

auto restart
conversion when
conversion
completes

idle
conversion

idle
conversion

idle
conversion

idle
conversion

idle
conversion

stop

converting

power source

power source stablization wait cycles

«
...
515
516
517
518
519
...
»

Содержание BAT32G1 9 Series






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для BAT32G1 9 Series

Бренд: Fairchild Страницы: 2

Бренд: Fairford Страницы: 233

Bell & Gossett Technologic PPS

Бренд: Xylem Страницы: 20

Бренд: Kantronics Страницы: 201

Бренд: bluelab Страницы: 39

Бренд: Planar Страницы: 162

Бренд: THK Страницы: 134

Arteor 5 742 74

Бренд: LEGRAND Страницы: 2

Commander Site Controller

Бренд: VeriFone Страницы: 34

Бренд: Hanbay Страницы: 13

SetPro MV Series

Бренд: Gigarise Страницы: 18

Бренд: Kamado Joe Страницы: 2

Бренд: Mi Casa Verde Страницы: 2

ITV1000-PR Series

Бренд: SMC Networks Страницы: 12

Бренд: 9g Products Страницы: 12

Бренд: Oracle Страницы: 76

Бренд: Phoenix Contact Страницы: 82

ControlPro CPRO-1010

Бренд: Pentair Страницы: 112

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды