ADTRAN ATLAS 550 Скачать руководство пользователя страница 34

Страница: 34 / 412

Section 2 Engineering Guidelines

ATLAS 550 System Manual

61200305L2-1B

T1/PRI Network Interface Module (P/N 1200307L1/L2), USOC RJ-48C

The T1/PRI Network Interface Module provides a single T1/PRI port (see Table 8 for the pinout) and
complies with the applicable ANSI and AT&T

standards. The T1/PRI Network Interface Module

provides the following functions:

•

AMI or B8ZS coding

•

Manual line build-out

•

D4 or ESF framing

•

Network performance monitoring and reporting

•

Test loopbacks with QRSS generation and checking

•

Extensive self-testing

Test Interface

The

MON

and

OUT

Bantam test jacks provide a bridged access jack for nonintrusive monitoring of the

incoming T1. When connected to this jack, configure the test equipment for bridged termination.

E1/PRA Network Interface Module (P/N 1200308L1), 15-pin female D-connector

The E1/PRA Network Interface Module provides a single E1/PRA port (see Table 9 on page 35) that pro-
vide the following functions:

•

AMI or HDB3 coding

•

Manual line build-out

•

NFAS, FAS, TS16 MF and CRC-4 framing

•

Supports CCS or CAS signaling

•

Network performance monitoring and reporting

•

Test loopbacks with QRSS generation and checking

•

Extensive self-testing

Table 8. T1/PRI Network Interface Module RJ-48C Pinout

Pin

Name

Description

RXDATA-RING (R1)

Receive data from the network

RXDATA-TIP (T1)

Receive data from the network

–––––

Unused

TXDATA-RING (R)

Transmit data toward the network

TXDATA-TIP (T)

Transmit data toward the network

6, 7, 8

–––––

Unused

Содержание ATLAS 550





























































































































































































































































































































































































































Результаты поиска

Содержание ATLAS 550

Отзывы:

Похожие инструкции для ATLAS 550

Бренды по названию

Популярные бренды

ADTRAN ATLAS 550, Системное руководство

Результаты поиска

Содержание ATLAS 550

Отзывы:

Похожие инструкции для ATLAS 550

Бренды по названию

Популярные бренды