ADTRAN ATLAS 550 Скачать руководство пользователя страница 249

Страница: 249 / 412

ATLAS 550 System Manual

Section 4 User Interface Guide

61200305L2-1B

249

IRCUIT

TATUS

> T

EST

> N

EXT

IME

Read security: 5

(Not visible unless

EST

ALL

is configured for non-manual operation in the

NTERFACE

ONFIG

for the

IRCUIT

ACKUP

NDPOINT

Displays the date and time of the next schedule test call to be made through

this dedicated dial backup circuit.

IRCUIT

TATUS

> T

EST

> L

AST

EST

TATUS

Read security: 5

Displays the status of the last test call made through this dedicated dial backup circuit. The following status
messages may display:

IRCUIT

TATUS

> T

EST

> P

ASS

: F

AIL

Read security: 5

Displays the number of successful and unsuccessful test calls made through this dedicated dial backup
circuit.

IRCUIT

TATUS

> T

EST

> T

EST

Write security: 5; Read security: 5

Press to initiate a test call on the dedicated dial backup circuit.

DLE

No current test call on this dedicated dial backup circuit

ASSED

Passed last manual or scheduled test

AILED

Failed last manual or scheduled test

Содержание ATLAS 550





























































































































































































































































































































































































































Результаты поиска

Содержание ATLAS 550

Отзывы:

Похожие инструкции для ATLAS 550

Бренды по названию

Популярные бренды

ADTRAN ATLAS 550, Системное руководство

Результаты поиска

Содержание ATLAS 550

Отзывы:

Похожие инструкции для ATLAS 550

Бренды по названию

Популярные бренды