ADTRAN ATLAS 550 Скачать руководство пользователя страница 194

Страница: 194 / 412

Section 4 User Interface Guide

ATLAS 550 System Manual

194

61200305L2-1B

ACKET

ANAGER

> P

ACKET

NDPNTS

> C

ONFIG

> P

ROT

Write security: 3; Read security: 5

Defines the protocol operating on this port.

RAME

ELAY

configures this packet endpoint for frame relay

signaling.

TBOP

configures this endpoint as transparent bit oriented protocol.

PPP

configures this packet

endpoint as point-to-point protocol.

SDLC

configures this packet endpoint as an SDLC endpoint.

ACKET

ANAGER

> P

ACKET

NDPNTS

> C

ONFIG

> C

ONFIG

- F

RAME

ELAY

Write security: 3; Read security: 5

Contains the configuration parameters for this packet endpoint.

SDLC is only available for use with the Legacy Data Option Module (P/N 1200342L1).

IGNALING

OLE

Write security: 3; Read security: 5

Displays the frame relay signaling role for this packet endpoint. The following options indicate the
signaling role of this packet endpoint.

The remote device does not support frame relay signaling.

UTO

Detects the role of the device on the other end of the circuit and automatically sets
this packet endpoint to the appropriate value.

OTH

Operates in NNI mode.

ETWORK

Acts as the network side of the UNI interface.

SER

Acts as the user side of the UNI interface.

IGNALING

YPE

Write security: 3; Read security: 5

Displays the frame relay signaling type for this packet endpoint. The following options indicate the
signaling type for this packet endpoint.

UTO

Detects the signaling type of the device on the other end of the circuit and
automatically sets this packet endpoint to the same signaling type.

NNEX

Transmits and responds to ITU-T Q.933-A standards.

NNEX

Transmits and responds to ANSI T1.617-D standards.

LMI

Transmits and responds to Group of Four specifications.

SER

OLL

IMER

(T391)

Write security: 3; Read security: 5

Sets the polling interval to the network in seconds.

Содержание ATLAS 550





























































































































































































































































































































































































































Результаты поиска

Содержание ATLAS 550

Отзывы:

Похожие инструкции для ATLAS 550

Бренды по названию

Популярные бренды

ADTRAN ATLAS 550, Системное руководство

Результаты поиска

Содержание ATLAS 550

Отзывы:

Похожие инструкции для ATLAS 550

Бренды по названию

Популярные бренды