ADTRAN ATLAS 550 Скачать руководство пользователя страница 171 | Manualshive

Страница: 171 / 412

background image

ATLAS 550 System Manual

Section 4 User Interface Guide

61200305L2-1B

© 2004 ADTRAN, Inc.

171

M

ODULES

(N

X

T1HSSI) > HSSI M

ENUS

> C

ONFIG

> DCD (V.35)

Write security: 5; Read security: 5

(Available only on the NxT1 HSSI/V.35 Option Module - P/N 1200346L2.)

Determines the behavior of the

Data Carrier Detect (DCD) signal (also called RLSD on some interfaces). If se tot Normal, DCD will
generally be asserted when the interface is capable of passing data. If set to Forced On, DCD will always
be asserted. If set to Remote RTS, the value of DCD will track the value of the remote unit’s RTS signal.

M

ODULES

(N

X

T1HSSI) > HSSI M

ENUS

> C

ONFIG

> CA

Write security: 5; Read security: 5

(Not applicable in V.35 mode.)

Asserts the data Communications equipment

A

VAILABLE

signal from the

DCE. CA will be asserted by the DCE, independently of TA, when the DCE is prepared to both send and
receive data to and from the DTE. This indicates that the DCE has obtained a valid data communications
channel. Data transmission should not commence until TA has also been asserted by the DTE.

M

ODULES

(N

X

T1HSSI) > HSSI M

ENUS

> T

EST

Write security: 4; Read security: 5

Provides access to testing functionality for the HSSI and HSSI/V.35 interfaces for the NxT1 HSSI or NxT1
HSSI/V.35 Option Modules.

M

ODULES

(N

X

T1HSSI) > HSSI M

ENUS

> T

EST

> P

ORT

Read security: 5

Indicates the operating port number. The NxT1 HSSI and NxT1 HSSI/V.35 Option Modules have one
available HSSI (or HSSI/V.35) interface.

M

ODULES

(N

X

T1HSSI) > HSSI M

ENUS

> T

EST

> L

OCAL

L

PBK

Write security: 4; Read security: 5

Activates a local loopback on the HSSI interface. The following local loopbacks are available:

DCD is not configurable when the Interface Automatic Deactivation (

I

FCE

A

UTO

D

EACT

)

feature is

O

N

.

L

OCAL

L

INE

Activates a loopback of the received T1 data streams at the DTE interface.

T1 F

RAMER

Activates a loopback of the received T1 data streams after the data has been
processed by the T1 framer located on the NxT1 HSSI or NxT1 HSSI/V.35
Option Modules. All data received during an active

T1 F

RAMER

local loopback

will be regenerated (re-framed) and transmitted back out the DTE interface.

L

OCAL

DTE

Activates a loopback of all data received at the DTE. All data received during an
active

L

OCAL

DTE

loopback will be echoed out the DTE interface.

«
...
169
170
171
172
173
...
»

Содержание ATLAS 550





























































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ATLAS 550

Бренд: Panasonic Страницы: 31

Бренд: Panasonic Страницы: 31

Бренд: NAiS Страницы: 199

Бренд: Panasonic Страницы: 38

Бренд: Panasonic Страницы: 36

Бренд: Panasonic Страницы: 179

Бренд: Panasonic Страницы: 23

Spartan-3A DSP FPGA Series

Бренд: Xilinx Страницы: 140

Бренд: Parker Страницы: 478

8745 MFC Ethernet

Бренд: Burkert Страницы: 70

Бренд: ccei Страницы: 16

Бренд: CDVI Страницы: 24

Бренд: Danfoss Страницы: 8

Бренд: Samson Страницы: 146

Бренд: Oasis Страницы: 22

Бренд: Bartels Mikrotechnik Страницы: 9

Бренд: Solcon Страницы: 65

Бренд: Canford Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды