ADTRAN ATLAS 550 Скачать руководство пользователя страница 124 | Manualshive

Страница: 124 / 412

background image

Section 4 User Interface Guide

ATLAS 550 System Manual

124

© 2004 ADTRAN, Inc.

61200305L2-1B

M

ODULES

(T1/PRI-2/4) > DS0 A

LARMS

Read security: 5

Displays per-DS0 alarm status. These alarms usually indicate the failure to receive the protocol that has
been configured for the DS0.

M

ODULES

(T1/PRI-2/4) > S

IG

S

TATUS

Read security: 5

Read-only field that indicates signaling of all 24 DS0s. The A/B bits for Rx (receive) and Tx (transmit)
DS0s are shown. Dashes display for those DS0s where robbed bit signaling (RBS) is not being transferred
by the ATLAS 550.

M

ODULES

(T1/PRI-2/4) > P

ERFORMANCE

C

URRENT

Write security: 3; Read security: 5

The performance fields (either current, 15-minute total, or 24-hour total) provide status on key
performance measures as specified in ANSI T1.403 and AT&T TR54016 for the T1/PRI port. Except for

C

LR

, these fields are all read-only. The monitored parameters include the following:

-

No Alarm DS0

D

D Channel Alarm (ISDN)

F

Frame Alarm (packet)

T

TBOP Alarm (packet)

P

PPP Alarm (packet)

P

RT

Displays the port number

C

LR

Clears performance information for the selected port

E

S

Errored Second (ES) is a second with one or more error events OR one or more
Out Of Frame events OR one or more Controlled Slips

B

ES

Bursty Errored Second (BES) is a second with more than one, but less than 320
error events

S

ES

Severely Errored Second (SES) is a second with 320 or more error events OR
one or more Out Of Frame events

S

EFS

Severely Errored Frame Second is a second that contains four consecutive
errored framing patterns.

L

OFC

Loss of Frame Count is a count of seconds in which a valid framing pattern
could not be obtained.

C

SS

Controlled Slip Second

U

AS

Unavailable Second is a second in which the T1 was not available for use (due to
outage, alarms, etc.).

L

CV

Line Code Violation indicates a mismatch in line coding (AMI or B8ZS)
somewhere in the network and is determined by receiving an invalid line
violation (bipolar violation).

«
...
122
123
124
125
126
...
»

Содержание ATLAS 550





























































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ATLAS 550

Бренд: Zolix Instruments Страницы: 22

Бренд: Paoli Страницы: 16

Бренд: NEC Страницы: 146

Max Charge MC-624

Бренд: Balmar Страницы: 8

MAX CHARGE MC-614

Бренд: Balmar Страницы: 20

Бренд: U.S. Divers Страницы: 22

Бренд: Watts Страницы: 24

Бренд: ZKTeco Страницы: 20

Бренд: ZKTeco Страницы: 8

Бренд: ZKTeco Страницы: 10

Бренд: ZKTeco Страницы: 121

Бренд: ZKTeco Страницы: 12

Бренд: ZKTeco Страницы: 6

Бренд: ZiLOG Страницы: 12

Бренд: NAiS Страницы: 144

Arteor 5 742 74

Бренд: LEGRAND Страницы: 2

Бренд: H3C Страницы: 48

Бренд: PPI Страницы: 27

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды