ADTRAN ATLAS 550 Скачать руководство пользователя страница 318 | Manualshive

Страница: 318 / 412

background image

Section 5 DLP-4

ATLAS 550 System Manual

318

© 2004 ADTRAN, Inc.

61200305L2-1B

1. Verify the ATLAS 550 IP address.

If you do not already have the IP Address for the ATLAS 550, obtain it from the network administrator
or manually check for the address in the

S

YSTEM

C

ONFIG

/E

THERNET

P

ORT

/IP A

DDRESS

menu of the

Network Management interface.

2. Ping the ATLAS 550 unit from a remote computer on the network.

Using a remote computer system connected to the LAN, perform an ICMP Ping on the IP Address of
the ATLAS 550. Verify that the unit responds properly. If the ATLAS 550 fails to respond, try the
following:

•

Verify that the proper IP Address, Subnet Mask, and Default Gateway are provisioned in the unit
(see DLP-3,

Setting IP Parameters for the ATLAS 550

) for details).

•

Verify that the ATLAS 550 is properly cabled into the LAN and that the Ethernet cable is properly
seated in the RJ-45 jack on the rear of the unit.

•

If the ATLAS 550 is connected to a hub or other network device that provides a carrier sense light
for each port, verify that the carrier sense light for the port to which the ATLAS 550 is connected
is lit. If this light is not lit, check the cabling between the hub and the shelf. The connection may
also be verified using the

ETHERNET

LED located on the front panel of the ATLAS 550.

•

Verify the IP Address, Subnet Mask, and Default Gateway on the remote computer system.

•

If none of these steps are successful, contact the LAN Administrator for assistance.

Perform the following steps in the order listed.

You must log in with maximum rights to modify the IP parameters on the ATLAS 550 (see
DLP-2, Logging in to the ATLAS 550).

Refer to the computer system’s documentation if you are unsure how to perform a Ping
command. Most computers running a networked version of Microsoft Windows™ or UNIX
allow a Ping to be performed by typing

ping <IP Address>

at a command line prompt.

Typically, the Ping program will respond by indicating that the remote IP Address has
responded in a certain amount of time or that no response was received.

Some versions of Ping will continue running until you explicitly tell them to stop. If the
program does not terminate on its own, type <CTRL+C> to stop the program.

«
...
316
317
318
319
320
...
»

Содержание ATLAS 550





























































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ATLAS 550

Бренд: ABB Страницы: 63

Бренд: Echelon Страницы: 40

Бренд: Abov Страницы: 138

Бренд: select solar Страницы: 2

Бренд: Zencontrol Страницы: 2

Бренд: Daikin Страницы: 2

Бренд: Advantech Страницы: 3

Бренд: Srne Страницы: 13

Бренд: Unika Страницы: 14

Бренд: Teradek Страницы: 10

Goulds ResiBoost RB111512

Бренд: Xylem Страницы: 40

Бренд: WAREMA Страницы: 4

Бренд: RIFT Actuators Страницы: 23

Бренд: Troy-Bilt Страницы: 11

MC DC-2.00 Series

Бренд: Hanbay Страницы: 7

Бренд: Resol Страницы: 60

Бренд: Bornay Страницы: 66

Бренд: Niko Страницы: 40

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды