ADTRAN ATLAS 550 Скачать руководство пользователя страница 248

Страница: 248 / 412

Section 4 User Interface Guide

ATLAS 550 System Manual

248

61200305L2-1B

IRCUIT

TATUS

> BKUP S

TATUS

ACKUP

TATUS

)

Read security: 5

The displayed string indicates the current status of the dedicated line. The following messages may display
in the

ACKUP

TATUS

field.

IRCUIT

TATUS

> L

INE

TATUS

Read security: 5

Displays the overall status of the connection. The following messages may display in the

INE

TATUS

field.

IRCUIT

TATUS

> D

ELAY

When present, this indicates that one ATLAS 550 has detected a change in state and is counting down to
delay/restore.

IRCUIT

TATUS

> T

EST

Write security: 1; Read security: 5

Contains a test activator and test status displays for dedicated dial backup circuits.

IRCUIT

TATUS

> T

EST

> L

AST

IME

Read security: 5

(Not visible until a circuit has been tested.)

Displays the date and time of the last test call made through

this dedicated dial backup circuit.

Backup was forced through the interface menu.

Restore was forced through the interface menu.

RIMARY

The link is active.

IALING

Attempting to dial the backup link.

ACKUP

AILED

Exceeded

EDIALS

ETRY

IAL

[

NUM

]

Will retry backup dialing in [num] seconds.

RIMARY

OWN

The link is in error and waiting on backup.

NSWERING

The link is answering a backup endpoint.

ACKUP

The link is in backup.

NKNOWN

Endpoints do not support (or are not configured) for monitoring.

CTIVE

The connection is up and running.

NACTIVE

The connection is down due to configuration (i.e., DTR is down).

ATA

LARM

The

ROM

endpoint is in data alarm.

ETWORK

LARM

The

endpoint is in network alarm.

ATA

LARM

Both the

ROM

endpoint and the

endpoint are in alarm.

ATA

NKNOWN

The status of the

ROM

endpoint is unknown.

Содержание ATLAS 550





























































































































































































































































































































































































































Результаты поиска

Содержание ATLAS 550

Отзывы:

Похожие инструкции для ATLAS 550

Бренды по названию

Популярные бренды

ADTRAN ATLAS 550, Системное руководство

Результаты поиска

Содержание ATLAS 550

Отзывы:

Похожие инструкции для ATLAS 550

Бренды по названию

Популярные бренды