ADTRAN ATLAS 550 Скачать руководство пользователя страница 192

Страница: 192 / 412

Section 4 User Interface Guide

ATLAS 550 System Manual

192

61200305L2-1B

ACKET

ANAGER

> P

ACKET

NDPNTS

> P

ERFORMANCE

> S

UBLINK

TATS

- F

RAME

ELAY

Write security: 3; Read security: 5

Displays frame relay performance statistics for supported packet endpoint sublinks. These statistic fields
reflect the total count since cleared.

These settings are not applicable for PPP or TBOP

ACKETS

Read security: 5

Number of packets received over this link.

LEAR

OUNTERS

Write security: 3; Read security: 5

Resets the Tx and Rx packet counters.

AME

Write security: 3; Read security: 5

Alphanumeric characters (up to 16 characters) to create a user-defined name for the sublink (PVC).

DLCI

Write security: 3; Read security: 5

Local address for each PVC as assigned by the carrier.

TATE

Write security: 3; Read security: 5\

Indicates if this particular sublink (PVC) has been defined as active by a full status poll, and also
indicates if the PVC is in backup mode.

CTIVE

PVC is active.

NACTIVE

PVC is inactive.

CTIVE

/BU

PVC is active, but in backup mode.

NACTIVE

/BU

PVC is inactive and in backup mode.

CKTS

Write security: 3; Read security: 5

Total number of frame relay user data packets transmitted over this PVC.

CKTS

Write security: 3; Read security: 5

Total number of frame relay user data packets received over this PVC.

Содержание ATLAS 550





























































































































































































































































































































































































































Результаты поиска

Содержание ATLAS 550

Отзывы:

Похожие инструкции для ATLAS 550

Бренды по названию

Популярные бренды

ADTRAN ATLAS 550, Системное руководство

Результаты поиска

Содержание ATLAS 550

Отзывы:

Похожие инструкции для ATLAS 550

Бренды по названию

Популярные бренды