ADTRAN ATLAS 550 Скачать руководство пользователя страница 144

Страница: 144 / 412

Section 4 User Interface Guide

ATLAS 550 System Manual

144

61200305L2-1B

ODULES

(U-BRI-4) > C

HANNEL

TATUS

> C

Read security: 5

(Channel) Displays the status of individual channels. The following symbols may display:

ODULES

(U-BRI-4) > P

ERFORMANCE

URRENT

Write security: 3; Read security: 5

The performance field provides status on key performance measures for each of the four BRI ports (U
interfaces). These fields are all read-only.

ODULES

(U-BRI-4) > C

ONFIGURATION

Write security: 3; Read security: 5

All of the following configurable parameters apply to the individual BRI U interfaces.

ODULES

(U-BRI-4) > C

ONFIGURATION

> P

Read security: 5

Displays the port number. There are 4 available interfaces on the Quad BRI-U Option Module.

ODULES

(U-BRI-4) > C

ONFIGURATION

> P

ORT

AME

Write security: 3; Read security: 5

Accepts any alpha-numeric name up to 16 characters long, to uniquely identify each port on the installed
module.

ODULES

(U-BRI-4) > T

EST

Write security: 5; Read security: 5

These options initiate different types of tests and display test results.

ODULES

(U-BRI-4) > T

EST

> P

Write security: 5; Read security: 5

Displays the port number. There are 4 available interfaces on the Quad BRI-U Option Module.

Unallocated channel

Inactive channel

Active B channel

Active D channel

Displays the port number.

EBE

Near-end block errors

EBE

Far-end block errors

Содержание ATLAS 550





























































































































































































































































































































































































































Результаты поиска

Содержание ATLAS 550

Отзывы:

Похожие инструкции для ATLAS 550

Бренды по названию

Популярные бренды

ADTRAN ATLAS 550, Системное руководство

Результаты поиска

Содержание ATLAS 550

Отзывы:

Похожие инструкции для ATLAS 550

Бренды по названию

Популярные бренды