ADTRAN ATLAS 550 Скачать руководство пользователя страница 131

Страница: 131 / 412

ATLAS 550 System Manual

Section 4 User Interface Guide

61200305L2-1B

131

ODULES

(V35N

-2) > PLL/FIFO > P

ORT

Read security: 5

Indicates the operating port. There are 2 available interfaces on the Dual Nx56/64 Option Module.

ODULES

(V35N

-2) > PLL/FIFO > PLL/FIFO

Read security: 5

Displays the state of the PLL and FIFO systems.

ODULES

(V35N

-2) > C

ONFIGURATION

Write security: 3; Read security: 5

All of the following configurable parameters apply to the individual V.35 ports.

ODULES

(V35N

-2) > C

ONFIGURATION

> P

Read security: 5

Displays the port number. There are 2 available interfaces on the Dual Nx56/64 Option Module.

ODULES

(V35N

-2) > C

ONFIGURATION

> P

ORT

AME

Write security: 3; Read security: 5

Accepts any alpha-numeric name up to 17 characters long, to uniquely identify each port on the Dual
Nx56/64 Option Module.

ODULES

(V35N

-2) > C

ONFIGURATION

> C

+/-

Write security: 3; Read security: 5

Controls the clock used by the ATLAS 550 to accept the transmit (TX) data from the DTE. This is usually
set to

ORMAL

. If the interface cable is long, causing a phase shift in the data, the clock can be set to

NVERTED

. This switches the phase of the clock, which compensates for a long cable.

ODULES

(V35N

-2) > C

ONFIGURATION

> D

ATA

Write security: 3; Read security: 5

Controls the inverting of the DTE data. This inversion can be useful when operating with a high-level data
link control (HDLC) protocol (often used as a means to ensure 1s density). Select either

ORMAL

NVERTED

. Data inversion configuration must match at both ends of the circuit.

OCK

PLL is locked (This is required to transfer data.)

RXE

Receive data FIFO empty.

RXF

Receive data FIFO full.

TXE

Transmit data FIFO empty.

TXF

Transmit data FIFO full.

Содержание ATLAS 550





























































































































































































































































































































































































































Результаты поиска

Содержание ATLAS 550

Отзывы:

Похожие инструкции для ATLAS 550

Бренды по названию

Популярные бренды

ADTRAN ATLAS 550, Системное руководство

Результаты поиска

Содержание ATLAS 550

Отзывы:

Похожие инструкции для ATLAS 550

Бренды по названию

Популярные бренды