ADTRAN ATLAS 550 Скачать руководство пользователя страница 244

Страница: 244 / 412

Section 4 User Interface Guide

ATLAS 550 System Manual

244

61200305L2-1B

EDICATED

APS

NDPT

- P

ACKET

NDPOINT

)

EDICATED

APS

NDPT

) > C

REATE

DIT

APS

> C

ONNECTS

Write security: 3; Read security: 5

To assign a packet endpoint to a physical port, select the port in the

ROM

LOT

ORT

field and configure

the

LOT

ORT

as follows:

EDICATED

APS

NDPT

) > C

REATE

DIT

APS

> C

ONNECTS

> T

LOT

ERVICE

Write security: 3; Read security: 5

Select

NDPNT

to activate a list of available packet endpoints in the

ORT

field.

EDICATED

APS

NDPT

) > C

REATE

DIT

APS

> C

ONNECTS

> T

ORT

/PEP

Write security: 3; Read security: 5

Press <Enter> and select the appropriate packet endpoint to assign the endpoint to a physical port.

EDICATED

APS

NDPT

) > C

REATE

DIT

APS

> C

ONNECTS

> T

ROM

ONFIG

Write security: 3; Read security: 5

Specifies the configuration for the

ROM

connection. The following selections apply to the packet

endpoint:

TD C

LOCK

OURCE

Write security: 3; Read security: 5

Configures the interface to provide or recover data clocking.

This clock source is used ONLY on the Legacy Data Option Module and cannot be used as
a source for system timing.

RANSMIT

DLE

ODE

Write security: 3; Read security: 5

Configures the port to use Flags or Ones as the idle code.

RANSMIT

DLE

ODE

Write security: 3; Read security: 5

Configures the ATLAS 550 to send idle code on the packet endpoint with marks or flags.

Содержание ATLAS 550





























































































































































































































































































































































































































Результаты поиска

Содержание ATLAS 550

Отзывы:

Похожие инструкции для ATLAS 550

Бренды по названию

Популярные бренды

ADTRAN ATLAS 550, Системное руководство

Результаты поиска

Содержание ATLAS 550

Отзывы:

Похожие инструкции для ATLAS 550

Бренды по названию

Популярные бренды