ADTRAN ATLAS 550 Скачать руководство пользователя страница 129

Страница: 129 / 412

ATLAS 550 System Manual

Section 4 User Interface Guide

61200305L2-1B

129

ODULES

(V35N

-2) > A

LARM

TATUS

Read security: 5

Displays the current alarm status.

ODULES

(V35N

-2) > A

LARM

TATUS

> P

Read security: 5

Indicates the port number.

ODULES

(V35N

-2) > A

LARM

TATUS

> A

LARMS

Read security: 5

Displays an alarm condition on the ATLAS 550 unit.

ODULES

(V35N

-2) > D

TATUS

Read security: 5

Shows the status of key DTE interface signals. An asterisk (*) indicates the presence of a signal and a
hyphen (-) indicates no signal present.

ODULES

(V35N

-2) > D

TATUS

> P

Read security: 5

Operating port number. There are 2 available interfaces on the Dual Nx56/64 Option Module.

ODULES

(V35N

-2) > D

TATUS

> D

TATUS

Read security: 5

The following signals are monitored (these options are read-only).

LIP

A rate mismatch exists between the DTE clock and the network-side clock (as
set by DS0 assignment).

The Nx port is not able to lock onto the clock provided by the network interface.

ERO

The DTE is sending an excessive number of consecutive zeroes to the network
interface.

The DTE is not providing an external transmit clock. This alarm displays only if
the Nx port is configured to get its transmit clock from the DTE.

A packet endpoint has detected missing or incorrect framing.

RTS

Request to send from DTE

Ring indicate to DTE

CTS

Clear to send to DTE

Transmit data from the DTE

DTR

Data terminal ready from DTE

Receive data toward the DTE

DSR

Data set ready to DTE

External clock present

DCD

Data carrier detect to DTE

Содержание ATLAS 550





























































































































































































































































































































































































































Результаты поиска

Содержание ATLAS 550

Отзывы:

Похожие инструкции для ATLAS 550

Бренды по названию

Популярные бренды

ADTRAN ATLAS 550, Системное руководство

Результаты поиска

Содержание ATLAS 550

Отзывы:

Похожие инструкции для ATLAS 550

Бренды по названию

Популярные бренды