ADTRAN ATLAS 550 Скачать руководство пользователя страница 221

Страница: 221 / 412

ATLAS 550 System Manual

Section 4 User Interface Guide

61200305L2-1B

221

OUTER

> IP > I

NTERFACES

> RIP

Write security: 2; Read security: 2

Configures routing information protocol (RIP) on this interface.

ODE

Write security: 2; Read security: 2

Allows RIP to be enabled or disabled on a per-interface basis.

NLY

RIP advertisements are periodically transmitted, but are not listened to
on this virtual circuit.

NLY

RIP advertisements are not transmitted on this virtual circuit, but they
are listened to.

AND

RIP advertisements are periodically transmitted and are listened to on
this virtual circuit.

RIP/M

ODE

ROTOCOL

, M

ETHOD

and

PDATE

will

not

be visible.

ROTOCOL

Write security: 2; Read security: 2

(Only visible if RIP is enabled.)

Sets the version of RIP being used on this interface. The options are

RIP V1

and

RIP V2

. If

RIP V2

is used, a new menu,

UTHENTICATION

, opens.

RIP V2

is used, a user-defined secret may have to be created.

ETHOD

Write security: 2; Read security: 2

(Only visible if RIP is enabled.)

Defines the method used to send RIP route advertisements. The

options are listed below:

ONE

All routes in the router table are advertised through this interface with
no modification of the routing metric.

PLIT

ORIZON

Only advertises routes not learned through this interface.

OISON

EVERSE

All routes are advertised, but the routes learned through this interface
are “poisoned” with an infinite route metric.

PDATES

Write security: 2; Read security: 2

Defines when RIP advertisements are transmitted.

Содержание ATLAS 550





























































































































































































































































































































































































































Результаты поиска

Содержание ATLAS 550

Отзывы:

Похожие инструкции для ATLAS 550

Бренды по названию

Популярные бренды

ADTRAN ATLAS 550, Системное руководство

Результаты поиска

Содержание ATLAS 550

Отзывы:

Похожие инструкции для ATLAS 550

Бренды по названию

Популярные бренды