ADTRAN ATLAS 550 Скачать руководство пользователя страница 324 | Manualshive

Страница: 324 / 412

background image

Section 5 DLP-6

ATLAS 550 System Manual

324

© 2004 ADTRAN, Inc.

61200305L2-1B

1. Connect to the ATLAS 550 using the

ETHERNET

interface.

If you are not already connected to the unit’s

ETHERNET

port using Telnet client software, use the

procedure in DLP-3,

Setting IP Parameters for the ATLAS 550

, to connect to the unit.

2. Log in to the unit using the read-write password (see DLP-2,

Logging in to the ATLAS 550

, for details).

3. Go to the

S

YSTEM

U

TILITY

menu and select

U

PDATE

F

IRMWARE

; press <Enter>.

4. Select

M

ODULE

S

LOT

and press <Enter>.

Select the appropriate module slot to update. The module slot for the ATLAS 550 system controller is
module slot 0.

5. Go to the

T

RANSFER

M

ETHOD

menu and select TFTP.

6. Enter into

TFTP S

ERVER

IP A

DDRESS

, the IP address of the network TFTP server.

7. Enter into

TFTP S

ERVER

F

ILENAME

, the full path name and filename of the update file.

8. From the

R

ESTART

S

CHEDULE

menu, select the time for the module to perform a restart after

completing the update.

R

ESTART

I

MMEDIATELY

A

FTER

U

PDATE

restarts the system immediately after the update is complete.

R

ESTART

A

T

S

PECIFIED

D

ATE

AND

T

IME

allows you to select when the updated system will restart. If you

select this option, a new field called

R

ESTART

D

ATE

AND

T

IME

displays below the current field. To use

that option, enter the time in 24-hour format (such as 23:00:00 for 11:00 pm). Enter the date in
mm-dd-yyyy format (for example, 06-30-2004).

9. Select

V

IEW

C

URRENT

U

PDATE

S

TATUS

to verify the progress of the current firmware update or to

identify any errors encountered during the download.

Refer to the table on the following page for a detailed description of messages found in this field.

10. Select

B

EGIN

F

IRMWARE

U

PDATE

to start the update. Enter

Y

to confirm the transfer and to set up the

module to receive the TFTP upload.

During the TFTP upload, the following status messages display in

C

URRENT

U

PDATE

S

TATUS

to

indicate the progress of the upload:

Perform the following steps in the order listed.

C

ONTACTING

S

ERVER

Indicates communication with the TFTP network server is trying to be
established with the specified server address in the

TFTP S

ERVER

IP

A

DDRESS

field.

B

EGINNING

TFTP

T

RANSFER

Indicates communication with the TFTP network server has been
established and the update file is being transferred between the ATLAS
550 and the TFTP network server.

C

OMPLETED

Indicates the ATLAS 550 successfully received the update file.

E

RROR

: F

ILE

N

OT

F

OUND

Indicates the TFTP network server was unable to locate the specified file
name or path in the

TFTP S

ERVER

F

ILENAME

field.

E

RROR

: A

CCESS

V

IOLATION

Indicates the TFTP network server denied the ATLAS 550 access to the
given update filename and path. Please verify appropriate user rights are
selected for the specified path.

«
...
322
323
324
325
326
...
»

Содержание ATLAS 550





























































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ATLAS 550

Бренд: Valcom Страницы: 6

Бренд: We Care Solar Страницы: 46

Бренд: Rain Bird Страницы: 18

Бренд: SMC Networks Страницы: 2

Бренд: Advanced Control Technologies Страницы: 3

Бренд: Eaton Страницы: 9

Бренд: Zennio Страницы: 13

Бренд: ST Страницы: 55

Бренд: National Instruments Страницы: 40

Бренд: National Instruments Страницы: 40

78K0S/K 1+ Series

Бренд: NEC Страницы: 44

78K0/L 3 - See it! Series

Бренд: NEC Страницы: 82

Бренд: NEC Страницы: 271

mPD17120 Subseries

Бренд: NEC Страницы: 289

Бренд: NEC Страницы: 324

Бренд: NEC Страницы: 406

Бренд: NEC Страницы: 410

Бренд: NEC Страницы: 515

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды