ADTRAN ATLAS 550 Скачать руководство пользователя страница 362

Страница: 362 / 412

Section 6 CFG-1

ATLAS 550 System Manual

362

61200305L2-1B

5. Configure the

FCE

ONFIG

options for the backup link. These include the Dial Backup parameters.

Navigate to the

FCE

ONFIG

option and press <Enter>. This action displays a list of the Dial Backup

options. (The options are described following the figure.)

)

RIGINATE

NSWER

RIGINATE

The ATLAS 550 will be the originating side in the event of a failure.

NSWER

The ATLAS 550 will answer any incoming calls, but only go into backup if an
error is detected.

NSWER

LWAYS

The ATLAS 550 will answer any incoming calls and immediately go into backup.

UTGOING

ALL

YPE

IGITAL

56K:

Data rate for the backup endpoint is set to 56kbps.

IGITAL

64K:

Data rate for the backup endpoint is set to 64kbps.

OURCE

The

OURCE

should remain in the default state unless it has been assigned elsewhere in the

configuration. Please refer to the

User Interface Guide

beginning on page 63 for a detailed

discussion of the

OURCE

field.

UTDIAL

UMBER

This field should contain the number you want the ATLAS 550 to dial upon going into backup.

ORCE

ODE

UTO

The ATLAS 550 will automatically follow the dial backup configuration
parameters to go into backup.

ORCED

The ATLAS 550 must be manually forced to go into backup upon detection of a
failure.

ISABLED

The ATLAS 550 will never go into backup regardless of data integrity.

Содержание ATLAS 550





























































































































































































































































































































































































































Результаты поиска

Содержание ATLAS 550

Отзывы:

Похожие инструкции для ATLAS 550

Бренды по названию

Популярные бренды

ADTRAN ATLAS 550, Системное руководство

Результаты поиска

Содержание ATLAS 550

Отзывы:

Похожие инструкции для ATLAS 550

Бренды по названию

Популярные бренды