ADTRAN ATLAS 550 Скачать руководство пользователя страница 316

Страница: 316 / 412

Section 5 DLP-3

ATLAS 550 System Manual

316

61200305L2-1B

1. Log in to the system with maximum rights (details are in DLP-2).

2. From the

YSTEM

ONFIG

menu, select the

THERNET

ORT

option and press <Enter>.

3. From the

YSTEM

ONFIG

THERNET

menu, select the

IP A

DDRESS

option and press <Enter>. Then

enter the appropriate IP address.

4. From the

YSTEM

ONFIG

THERNET

menu, select the

UBNET

ASK

option and press <Enter>. Then

enter the appropriate Subnet Mask.

5. From the

YSTEM

ONFIG

THERNET

menu, select the

EFAULT

ATEWAY

option and press <Enter>.

Then enter the appropriate Default Gateway.

6. Press the left-arrow key to highlight the

THERNET

submenu. This action saves your changes.

7. Escape out to the

YSTEM

ONFIG

menu and log off by pressing <CTRL + L>.

Perform the steps below in the order listed.

The next three steps will require confirmation after each change.

Содержание ATLAS 550





























































































































































































































































































































































































































Результаты поиска

Содержание ATLAS 550

Отзывы:

Похожие инструкции для ATLAS 550

Бренды по названию

Популярные бренды

ADTRAN ATLAS 550, Системное руководство

Результаты поиска

Содержание ATLAS 550

Отзывы:

Похожие инструкции для ATLAS 550

Бренды по названию

Популярные бренды