ADTRAN ATLAS 550 Скачать руководство пользователя страница 163 | Manualshive

Страница: 163 / 412

background image

ATLAS 550 System Manual

Section 4 User Interface Guide

61200305L2-1B

© 2004 ADTRAN, Inc.

163

M

ODULES

(N

X

T1 HSSI) > I

NFO

> S

ERIAL

N

UMBER

Read security: 5

Displays the serial number of the module.

M

ODULES

(N

X

T1 HSSI) > I

NFO

> A

SSEMBLY

R

EVISION

Read security: 5

Displays the assembly revision of the installed module.

M

ODULES

(N

X

T1 HSSI) > I

NFO

> F

IRMWARE

R

EVISION

Read security: 5

Displays the firmware revision of the installed module.

M

ODULES

(N

X

T1HSSI) > T1 M

ENUS

Read security: 5

Provides information about the four T1 interfaces located on the NxT1 HSSI and NxT1 HSSI/V.35 Option
Modules.

M

ODULES

(N

X

T1HSSI) > T1 M

ENUS

> A

LARM

S

TATUS

Read security: 5

Displays the current alarm status for each of the built-in T1 ports located on the NxT1 HSSI and NxT1
HSSI/V.35 Option Modules.

M

ODULES

(N

X

T1HSSI) > A

LARM

S

TATUS

> P

RT

Read security: 5

Indicates the operating port number for the selected T1 interface. There are four available T1 interfaces on
the NxT1 HSSI and NxT1 HSSI/V.35 Option Modules.

M

ODULES

(N

X

T1HSSI) > A

LARM

S

TATUS

> A

LARMS

Read security: 5

Provides a listing of possible alarm conditions on the T1 interface. An asterisk (*) indicates the presence of
an alarm condition and a hyphen (-) indicates no active alarm. The following alarms are monitored:

M

ODULES

(N

X

T1HSSI) > A

LARM

S

TATUS

> R

X

L

EVEL

Read security: 5

(Receive Level) Indicates the strength of the signal received on the port (in dB).

LOS

Indicates a loss of signal detected on the port interface.

R

ED

Indicates the inability to frame data received on the port. Alternately
referred to as Out of Frame (OOF).

Y

ELLOW

Receiving a remote alarm (RAI) on the interface from the far end.

B

LUE

Receiving unframed all ones from the port Alarm Indicator Signal (AIS).

DS0 A

LARM

Displays per-DS0 alarm status; that is, at least one DS0 channel is in
alarm if an asterisk (*) appears. These alarms usually indicate the failure
to receive the protocol that has been configured for the DS0.

«
...
161
162
163
164
165
...
»

Содержание ATLAS 550





























































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ATLAS 550

Leroy-Somer R180

Бренд: Nidec Страницы: 20

Бренд: GE Страницы: 425

Бренд: Camozzi Страницы: 33

Бренд: Camozzi Страницы: 64

Бренд: GAUGEMASTER Страницы: 2

Бренд: EasyIO Страницы: 19

Бренд: PAC Страницы: 17

Бренд: U-Prox Страницы: 25

Бренд: Atari Страницы: 3

Бренд: Grosvenor Страницы: 5

Бренд: Brooks Страницы: 66

ERO-32AP-0 V1.4

Бренд: Darco Страницы: 14

Бренд: Rainmachine Страницы: 22

Бренд: J+J Страницы: 91

Touch Screen Controller EX112

Бренд: 3M Страницы: 40

komplete kontrol s series

Бренд: Native Instruments Страницы: 338

Бренд: Rain Страницы: 8

Бренд: Autopilot Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды