ADTRAN ATLAS 550 Скачать руководство пользователя страница 104

Страница: 104 / 412

Section 4 User Interface Guide

ATLAS 550 System Manual

104

61200305L2-1B

ODULES

(T1/PRI-1) > I

NFO

Read security: 5

Displays general information about the T1/PRI Network Interface Module as follows:

ODULES

(T1/PRI-1) > I

NFO

> P

ART

UMBER

Read security: 5

Displays the part number of the T1/PRI Network Interface Module.

ODULES

(T1/PRI-1) > I

NFO

> S

ERIAL

UMBER

Read security: 5

Displays the module’s serial number.

ODULES

(T1/PRI-1) > I

NFO

> A

SSEMBLY

EVISION

Read security: 5

Displays the assembly revision of the module.

ODULES

(T1/PRI-1) > A

LARM

TATUS

Read security: 5

Displays the current T1 alarm status.

ODULES

(T1/PRI-1) > A

LARM

TATUS

> P

Read security: 5

Indicates the port number.

ODULES

(T1/PRI-1) > A

LARM

TATUS

> A

LARMS

Read security: 5

Displays an alarm condition on the ATLAS 550 unit. Press <Enter> to access this menu item.

ODULES

(T1/PRI-1) > R

EVEL

ECEIVE

EVEL

)

Indicates the strength of the signal (in dB) received on the port.

LOS

Indicates a loss of signal detected on port interface.

Indicates inability to frame data received on the port. Alternately referred to as
Out of Frame (OOF).

ELLOW

Receiving remote alarm (RAI) on port.

LUE

Receiving unframed all ones from the port Alarm Indicator Signal (AIS).

DS0 A

LARM

Displays per-DS0 alarm status; that is, at least one DS0 channel is in alarm if an
asterisk (*) appears. These alarms usually indicate the failure to receive the
protocol that has been configured for the DS0.

Содержание ATLAS 550





























































































































































































































































































































































































































Результаты поиска

Содержание ATLAS 550

Отзывы:

Похожие инструкции для ATLAS 550

Бренды по названию

Популярные бренды

ADTRAN ATLAS 550, Системное руководство

Результаты поиска

Содержание ATLAS 550

Отзывы:

Похожие инструкции для ATLAS 550

Бренды по названию

Популярные бренды