ADTRAN ATLAS 550 Скачать руководство пользователя страница 189

Страница: 189 / 412

ATLAS 550 System Manual

Section 4 User Interface Guide

61200305L2-1B

189

ACKET

ANAGER

> P

ACKET

NDPNTS

> S

TATUS

> S

TATE

- F

RAME

ELAY

Read security: 5

(Valid only for Frame Relay endpoints.)

Indicates the frame relay signaling state on this packet endpoint.

The possible states are defined below.

ACKET

ANAGER

> P

ACKET

NDPNTS

> S

TATUS

> S

TATE

- PPP

Read security: 5

(Valid only for PPP endpoints.)

Indicates the status of the PPP negotiation.The possible states are defined

below.

ACKET

ANAGER

> P

ACKET

NDPNTS

> S

TATUS

> C

URRENT

ORT

Read security: 5

Displays the connections for the packet endpoint. The letter

in this field indicates that this packet

endpoint is used in the

ACKET

NCTS

map. The remainder of the field indicates the physical port this

packet endpoint is connected to in the

EDICATED

. If the port is a channelized interface such as a T1,

the DS0 assignment is also provided.

Indicates that there is active frame relay signaling on this endpoint. The
packet endpoint must be defined by the frame relay configuration
settings to show active frame relay signaling.

OWN

The packet endpoint stays in this state only when the physical line is
down.

NITIAL

This is the first state of LCP negotiation. If the packet endpoint is connected
to a physical port in the

EDICATED

, this state will usually transition to

the

TARTING

state to begin the PPP negotiation.

TARTING

The packet endpoint stays in this state only when the physical line is down.

- S

ENT

The packet endpoint has sent an LCP configuration request to the peer and
is waiting for an “acknowledge.”

- R

ECVD

The packet endpoint has received an “acknowledge” from the peer for the
sent configuration request.

- S

ENT

The packet endpoint has acknowledged the peer’s configuration request,
but the peer has not acknowledged us.

PENED

LCP negotiation on the packet endpoint has finished; authentication, if
enabled, occurs now.

LOSING

The packet endpoint has sent the peer a “terminate” request and is waiting
for the peer’s acknowledgement.

LOSED

The packet endpoint has received the peer’s acknowledgement to the sent
terminate request; this is followed by the initial state.

TOPPING

The packet endpoint has received a terminate request from the peer.

TOPPED

The packet endpoint has acknowledged the peer’s terminate request.

ONNECTED

The packet endpoint is not connected to the router in the

ACKET

NCTS

menu.

Содержание ATLAS 550





























































































































































































































































































































































































































Результаты поиска

Содержание ATLAS 550

Отзывы:

Похожие инструкции для ATLAS 550

Бренды по названию

Популярные бренды

ADTRAN ATLAS 550, Системное руководство

Результаты поиска

Содержание ATLAS 550

Отзывы:

Похожие инструкции для ATLAS 550

Бренды по названию

Популярные бренды