ADTRAN ATLAS 550 Скачать руководство пользователя страница 56 | Manualshive

Страница: 56 / 412

background image

Section 3 Network Turnup Procedure

ATLAS 550 System Manual

56

© 2004 ADTRAN, Inc.

61200305L2-1B

6.

SUPPLYING POWER TO THE UNIT

AC-Powered Systems

The AC-powered ATLAS 550 comes equipped with a detachable 6-foot power cord with a 3-prong plug
for connecting to a grounded power receptacle. As shipped, the ATLAS 550 is set to factory default
conditions. To power-up the unit, ensure that the unit is properly connected to an appropriate power source
and turn on the unit using the on/off switch on the back panel.

DC-Powered Systems

The DC-powered ATLAS 550 comes equipped with a DC power supply to furnish the voltages necessary
for proper backplane operation. As shipped, the ATLAS 550 is set to factory default conditions. After
installing the unit and any option modules, the ATLAS 550 is ready for power-up.

7.

INSTALLING NETWORK AND OPTION MODULES

Figure 2 shows the option slot numbering designation as viewed from the back of the ATLAS 550.

Figure 2. ATLAS 550 Slot Designation (Back Panel)

•

Power to the ATLAS 550 AC system must be from a grounded 90-130/190-240 VAC,
50/60 Hz source.

•

The power receptacle uses double-pole, neutral fusing.

•

Maximum recommended ambient operating temperature is 45

o

C.

•

Power to the ATLAS 550 DC system must be from a reliably grounded -48 VDC or

+24 VDC source which is electrically isolated from the AC source.

•

Install this unit in accordance with Article 400 and 364.8 of the NEC NFPA 70.

•

The branch circuit overcurrent protection shall be a fuse or circuit breaker rated
minimum 60 VDC, maximum 10A.

•

A readily accessible disconnect device that is suitably approved and rated shall be
incorporated in the field wiring.

•

Maximum recommended ambient operating temperature is 45ºC.

O

I

ALL EMPTY SLOTS MUST BE

COVERED WITH BLANK PANELS

500 Series

500 Series

500 Series

CAUTION: FOR CONTINUED PROTECTION

AGAINST RISK OF FIRE, REPLACE ONLY

WITH SAME TYPE AND RATING OF FUSE.

ETHERNET

ADMIN

RELAY

ALARM

MON

COM

NO

NC

500 Series

NETWORK 2

NETWORK 1

500 Series

500 Series

FUSE RATING: 2A/250V SLO-BLO

90-240VAC, 2A 50/60Hz

1

2

3

4

1

3

2

4

Ntwk 1

Ntwk 2

«
...
54
55
56
57
58
...
»

Содержание ATLAS 550





























































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ATLAS 550

Бренд: Acclaim Lighting Страницы: 32

Бренд: Harpo Страницы: 35

Бренд: Hardi Страницы: 2

Бренд: YASKAWA Страницы: 340

Бренд: Watlow Страницы: 20

1020 CAN-RS232-RS422 MFL

Бренд: PENKO Страницы: 29

Optidrive Elevator

Бренд: Invertek Страницы: 5

Бренд: Techtrol Страницы: 4

VARIOMATIC SARV 07.1

Бренд: AUMA Страницы: 32

Бренд: Consort Страницы: 4

Бренд: TAC Страницы: 76

Kade KZ-700-U/H

Бренд: ATT Holding Страницы: 12

Alicat Scientific MC

Бренд: Halma Страницы: 2

Бренд: Sorel Страницы: 20

Бренд: digitalview Страницы: 18

Бренд: Nitrous Express Страницы: 20

Бренд: Eaton Страницы: 3

Бренд: iXBlue Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды