ADTRAN ATLAS 550 Скачать руководство пользователя страница 226 | Manualshive

Страница: 226 / 412

background image

Section 4 User Interface Guide

ATLAS 550 System Manual

226

© 2004 ADTRAN, Inc.

61200305L2-1B

I

N

D

ELIVERS

The total number of input datagrams successfully delivered to IP user-protocols
(including ICMP).

O

UT

R

EQUESTS

The total number of IP datagrams which local IP user-protocols (including ICMP)
supplied to IP in requests for transmission. Note that this counter does not include
any datagrams counted in

F

ORW

D

ATAGRAMS

.

O

UT

D

ISCARDS

The number of output IP datagrams for which no problem was encountered to
prevent their transmission to their destination, but which were discarded (e.g., for
lack of buffer space). Note that this counter would include datagrams counted in

F

ORW

D

ATAGRAMS

if any such packets met this (discretionary) discard criterion.

O

UT

N

O

R

OUTES

The number of IP datagrams discarded because no route could be found to transmit
them to their destination. Note that this counter includes any packets counted in

F

ORW

D

ATAGRAMS

which meet this “no-route” criterion. Note also that this includes

any datagrams which a host cannot route because all of its default gateways are
down.

R

EASM

T

IMEOUT

The maximum number of seconds which received fragments are held while they
are awaiting reassembly at this ATLAS 550.

R

EASM

R

EQDS

The number of IP fragments received which needed to be reassembled at this
ATLAS 550.

R

EASM

OK

S

The number of IP datagrams successfully reassembled.

R

EASM

F

AILS

The number of failures detected by the IP reassembly algorithm (for whatever
reason: timed out, errors, etc.). Note that this is not necessarily a count of discarded
IP fragments since some algorithms (notably RFC 815s) can lose track of the
number of fragments by combining them as they are received.

F

RAG

OK

S

The number of IP datagrams that have been successfully fragmented at this
ATLAS 550.

F

RAG

F

AILS

The number of IP datagrams that have been discarded because they needed to be
fragmented at this ATLAS 550 but could not be, e.g., because their “Don't
Fragment” flag was set.

F

RAG

C

REATES

The number of IP datagram fragments that have been generated as a result of
fragmentation at this ATLAS 550.

C

LEAR

Clears the accumulated statistics.

Table 7. ICMP Statistics

Name

Description

I

N

M

SGS

The total number of ICMP messages which the ATLAS 550 received. Note that
this counter includes all those counted by

I

N

E

RRORS

.

I

N

E

RRORS

The number of ICMP messages which the ATLAS 550 received but determined as
having errors (bad ICMP checksums, bad length, etc.)

Table 6.

IP Statistics

(Continued)

Name

Description

«
...
224
225
226
227
228
...
»

Содержание ATLAS 550





























































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ATLAS 550

Бренд: Facility Explorer Страницы: 4

Бренд: Paoli Страницы: 16

Бренд: Ascon tecnologic Страницы: 16

Бренд: KIOUR Страницы: 3

ESP32-C3 Series

Бренд: Espressif Systems Страницы: 30

Бренд: SFC Страницы: 48

Бренд: Satel Страницы: 8

Бренд: Belimo Страницы: 6

Бренд: Danfoss Страницы: 16

Бренд: Ibiza Страницы: 37

Бренд: Danfoss Страницы: 8

Бренд: Kilews Страницы: 11

Бренд: Dontek Страницы: 10

Бренд: Knoll Страницы: 3

Бренд: gefran Страницы: 16

Бренд: ST Страницы: 25

Бренд: FPTech Страницы: 11

Бренд: Link4 Страницы: 70

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды