ADTRAN ATLAS 550 Скачать руководство пользователя страница 177 | Manualshive

Страница: 177 / 412

background image

ATLAS 550 System Manual

Section 4 User Interface Guide

61200305L2-1B

© 2004 ADTRAN, Inc.

177

M

ODULES

(VCOM-

X

) > C

ONFIG

> C

ONFIGURE

VCOM D

EVICES

> D

EVICE

Read security: 5

Indicates the resource number of the packet voice device listed. On the ATLAS 550, packet voice devices
are numbered 1-24.

M

ODULES

(VCOM-

X

) > C

ONFIG

> C

ONFIGURE

VCOM D

EVICES

> S

TATE

Write security: 4; Read security: 5

Controls the configuration state of the individual packet voice device. The ATLAS 550 determines the
initial configuration state of each device. ATLAS uses this configuration information to determine which
packet voice devices are functional and may be used, which are defective and should not be used, or which
are not present on the module and should not be used. Users who suspect an individual packet voice device
of improper operation can manually disable that device to prevent ATLAS from attempting to use it. The
possible states are defined below.

M

ODULES

(VCOM-

X

) > C

ONFIG

> G

AIN

S

ETTINGS

Write security: 5; Read security: 5

Contains the configuration for output and input gain for the VCOM Resource Module.

M

ODULES

(VCOM-

X

) > C

ONFIG

> G

AIN

S

ETTINGS

> O

UTPUT

G

AIN

Write security: 3; Write security: 5

Output gain is applied in the receive direction. Choices range from

+12 dB

(loudest) to

-12 dB

(softest) in

3 dB increments. This setting takes affect immediately.

M

ODULES

(VCOM-

X

) > C

ONFIG

> G

AIN

S

ETTINGS

> I

NPUT

G

AIN

Write security: 3; Write security: 5

Input gain is applied in the transmit direction. Choices range from

-12 dB

(softest) to

+12 dB

(loudest) in

3 dB increments. This setting does not affect currently active calls.

M

ODULES

(VCOM-

X

) > C

ONFIG

> C

URRENT

F

AX

S

TATUS

Write security: 5; Read security: 5

Enables or disables fax over packet capability using the voice compression module.

D

EFERRED

Devices which fail built-in testing are automatically marked as

D

EFERRED

,

indicating that the ATLAS 550 declines to use the device.

A

VAILABLE

The device is properly functioning and can be used when required. The
ATLAS 550 automatically marks devices that pass built-in testing as

A

VAILABLE

.

D

ISABLED

Marking a device as

D

ISABLED

prevents the ATLAS 550 from attempting to use

it. You can mark a device currently in use as disabled without disturbing the
connection, but the device will not be eligible for use in future calls until you
re-mark it as

A

VAILABLE

. This is helpful if you suspect that a particular device is

malfunctioning and do not want any calls routed to it.

«
...
175
176
177
178
179
...
»

Содержание ATLAS 550





























































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ATLAS 550

Бренд: Facility Explorer Страницы: 4

Бренд: Rayrun Страницы: 4

Бренд: Parker Страницы: 29

Бренд: ZKTeco Страницы: 43

Бренд: Danfoss Страницы: 30

Бренд: Barco Страницы: 4

Бренд: G-Tech Страницы: 26

Бренд: LevelOne Страницы: 314

Бренд: Galcon Страницы: 24

freescale Kinetics TWR-K60N512-KEIL

Бренд: NXP Semiconductors Страницы: 5

Infilex ZM WY5122

Бренд: Azbil Страницы: 12

Бренд: AlfaRadio Страницы: 23

Бренд: Danfoss Страницы: 18

Бренд: Watt Stopper Страницы: 3

Бренд: ZoneVu Страницы: 30

Бренд: Genave Страницы: 21

GUARDIAN CP DC2

Бренд: Amtrol Страницы: 12

Бренд: pleiger Страницы: 59

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды