ADTRAN ATLAS 550 Скачать руководство пользователя страница 224

Страница: 224 / 412

Section 4 User Interface Guide

ATLAS 550 System Manual

224

61200305L2-1B

OUTER

> IP > P

ING

> T

TATS

Read security: 2

Displays the number of ping requests transmitted (

n txed

), the number of ping replies received (

n rxed

)

and the number of ping requests that were lost (

n lost

OUTER

> IP > P

ING

> R

ESET

TATS

Write security: 2; Read security: 2

Resets all ping statistics to zero. If the ping client is active, this menu will stop it.

OUTER

> IP > P

ING

> S

TART

TOP

Write security: 2; Read security: 2

If the ping client is currently idle, this menu sends pings to the specified address. If the ping client is active,
the menu stops sending pings.

OUTER

> IP > T

ELNET

LIENT

Write security: 2; Read security: 2

Allows a user to open a Telnet session to any device listed in the ATLAS 550 route table.

OUTER

> IP > T

ELNET

LIENT

> A

DDRESS

Write security: 2; Read security: 2

Defines the IP address assigned to the remote unit you are trying to connect to.

OUTER

> IP > T

ELNET

LIENT

> E

SCAPE

HAR

Write security: 2; Read security: 2

Defines the Telnet client escape character. Typing the combination characters will close the active Telnet
session to the remote unit specified in the

DDRESS

field.

OUTER

> IP > T

ELNET

LIENT

> P

ORT

Write security: 2; Read security: 2

Defines the port used in the remote login session. Default (for Telnet) is

OUTER

> IP > T

ELNET

LIENT

> C

ONNECT

Write security: 2; Read security: 2

Activator used to start a Telnet session to the remote unit configured in the

DDRESS

field.

PTION

EYSTROKE

^ ]

<CTRL > + ]

^ \

<CTRL > + \

^ [

<CTRL > + [

^ ^

<CTRL > + <Shift > + 6

^ _

<CTRL > + <Shift > + -

Содержание ATLAS 550





























































































































































































































































































































































































































Результаты поиска

Содержание ATLAS 550

Отзывы:

Похожие инструкции для ATLAS 550

Бренды по названию

Популярные бренды

ADTRAN ATLAS 550, Системное руководство

Результаты поиска

Содержание ATLAS 550

Отзывы:

Похожие инструкции для ATLAS 550

Бренды по названию

Популярные бренды