ADTRAN ATLAS 550 Скачать руководство пользователя страница 245

Страница: 245 / 412

ATLAS 550 System Manual

Section 4 User Interface Guide

61200305L2-1B

245

EDICATED

APS

OICE

- P

ACKET

OICE

NDPOINT

)

EDICATED

APS

OICE

) > C

REATE

DIT

APS

> C

ONNECTS

Write security: 3; Read security: 5

Enters the dedicated map connections. Press <Enter > to activate the submenus.

EDICATED

APS

OICE

) > C

REATE

DIT

APS

> C

ONNECTS

> T

LOT

ERVICE

Write security: 3; Read security: 5

Select

OICE

to activate a list of available packet endpoints in the

ORT

field.

EDICATED

APS

OICE

) > C

REATE

DIT

APS

> C

ONNECTS

> T

ORT

/PEP

Write security: 3; Read security: 5

Press <Enter> and select the appropriate packet endpoint from the drop-down list.

EDICATED

APS

OICE

) > C

REATE

DIT

APS

> C

ONNECTS

> T

ROM

ONFIG

Write security: 3; Read security: 5

Specifies the configuration for the

ROM

connection. The following selections apply to the

OICE

connections:

ECEIVE

DLE

ODE

Write security: 3; Read security: 5

Defines the idle code (either marks or flags) the ATLAS 550 should expect on the selected packet
endpoint.

DLCI

Write security: 3; Read security: 5

Press <Enter > and select the appropriate DLCI from the drop-down list.

OICE

ORT

Write security: 3; Read security: 5

Identifies the voice port address of the remote unit. Express units support ports 1 and 2. A remote
ATLAS supports ports 1 through 255.

ONFLICT

EPORT

Write security: 3; Read security: 5

Describes existing conflicts. Potential problems include DLCI unavailable or Voice port already in
use.

Содержание ATLAS 550





























































































































































































































































































































































































































Результаты поиска

Содержание ATLAS 550

Отзывы:

Похожие инструкции для ATLAS 550

Бренды по названию

Популярные бренды

ADTRAN ATLAS 550, Системное руководство

Результаты поиска

Содержание ATLAS 550

Отзывы:

Похожие инструкции для ATLAS 550

Бренды по названию

Популярные бренды