ADTRAN ATLAS 550 Скачать руководство пользователя страница 84

Страница: 84 / 412

Section 4 User Interface Guide

ATLAS 550 System Manual

61200305L2-1B

YSTEM

ONFIG

> SNMP > SNMP C

OMMUNITIES

> IP A

DDRESS

Write security: 3; Read security: 5

Specifies the IP address of the network manager.

YSTEM

ONFIG

> SNMP > SNMP C

OMMUNITIES

> P

RIVILEGES

Write security: 3; Read security: 5

Defines the

(read-only) and

(read and write) privileges.

YSTEM

ONFIG

> SNMP > SNMP C

OMMUNITIES

> G

AME

Write security: 3; Read security: 5

Defines the community name for

access. This value must match the

name defined on the network

management station (NMS).

UBLIC

is the default name.

YSTEM

ONFIG

> SNMP > SNMP C

OMMUNITIES

> S

AME

Write security: 3; Read security: 5

Defines the community name for

access. This value must match either the

name defined

on the network management station (NMS).

UBLIC

is the default name.

YSTEM

ONFIG

> SNMP > T

RAP

RANSMISSION

Write security: 3; Read security: 5

Enables and disables SNMP trap transmission.

YSTEM

ONFIG

> SNMP > A

UTHEN

RAP

RANSMISSION

Write security: 3; Read security: 5

Enables and disables the authentication failure trap. The authentication failure trap is sent (when

NABLED

)

each time authenticated access to the ATLAS 550 fails.

YSTEM

ONFIG

> SNMP > T

RAPS

ESTINATION

Write security: 3; Read security: 5

Defines the destination for SNMP traps as follows:

YSTEM

ONFIG

> SNMP > T

RAPS

ESTINATION

> IP A

DDRESS

Write security: 3; Read security: 5

Identifies the IP address for the network management station (NMS) to send traps to.

YSTEM

ONFIG

> SNMP > T

RAPS

ESTINATION

> C

OMMUNITY

Write security: 3; Read security: 5

Defines the community name for trap destinations. This name must match the community name defined on
the network management station (NMS).

Содержание ATLAS 550





























































































































































































































































































































































































































Результаты поиска

Содержание ATLAS 550

Отзывы:

Похожие инструкции для ATLAS 550

Бренды по названию

Популярные бренды

ADTRAN ATLAS 550, Системное руководство

Результаты поиска

Содержание ATLAS 550

Отзывы:

Похожие инструкции для ATLAS 550

Бренды по названию

Популярные бренды