ADTRAN ATLAS 550 Скачать руководство пользователя страница 222 | Manualshive

Страница: 222 / 412

background image

Section 4 User Interface Guide

ATLAS 550 System Manual

222

© 2004 ADTRAN, Inc.

61200305L2-1B

R

OUTER

> IP > I

NTERFACES

> P

ROXY

ARP

Write security: 2; Read security: 2

Enables or disables Proxy ARP on this interface. Allows the network portion of a group of addresses to be
shared among several physical network segments. When

E

NABLED

, and an ARP (address resolution

protocol) request is received on the Ethernet port, the address is looked-up in the IP routing table. If the
forwarding port is not on the Ethernet port and the route is not the default route, the router answers the
request with its own hardware address. When

D

ISABLED

(default), the router only responds to ARP request

received for its own address.

The ARP protocol itself provides a way for devices to create a mapping between physical (i.e., Ethernet)
addresses and logical IP addresses.

P

ROXY

ARP

uses the mapping feature by instructing a router to answer

ARP requests as a “proxy” for the IP addresses behind one of its ports. The device which sent the ARP
request then correctly assumes that it can reach the requested IP address by sending packets to the physical
address that was returned. This technique effectively hides the fact that a network has been (further)
subnetted.

R

OUTER

> IP > G

LOBAL

Write security: 2; Read security: 2

Provides a way to configure various settings for the Ethernet port. The following menus are available for
review and editing:

R

OUTER

> IP > G

LOBAL

> D

EFAULT

G

ATEWAY

Write security: 2; Read security: 2

Defines or changes the default gateway. Enter the default gateway address by entering a decimal number
into the appropriate field and then pressing <Enter> to move to the next field. You will need a default
gateway if the LAN contains multiple segments. This address is composed of four decimal numbers, each
in the range of 0 to 255, separated by periods. This value is set to

0.0.0.0

by default. Contact your LAN

administrator for the appropriate address.

R

OUTER

> IP > G

LOBAL

> D

EFAULT

M

ETRIC

Write security: 2; Read security: 2

Defines the default gateway metric. Enter the default gateway metric by pressing <Enter> and entering a
decimal number.

P

ERIODIC

RIP advertisements are periodically transmitted.

T

RIGGERED

RIP advertisements are transmitted only when new routes are learned,
and learned routes do not age.

A

UTHENTICATION

Write security: 2; Read security: 2

Defines the secret used to advertise routes when using RIP V2.

R

EDISTRIBUTE

D

EFAULT

G

ATEWAY

Write security: 2; Read security: 2

Enables or disables the transmission of the Default Gateway to be sent with RIP on a per interface
basis.

«
...
220
221
222
223
224
...
»

Содержание ATLAS 550





























































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ATLAS 550

Бренд: Fantech Страницы: 2

Бренд: Federal Signal Corporation Страницы: 34

xPico 200 Series

Бренд: Lantronix Страницы: 7

Бренд: Lantronix Страницы: 3

Бренд: Lantronix Страницы: 15

Бренд: Namron Страницы: 3

Бренд: National Instruments Страницы: 78

Cutler-Hammer Jockey

Бренд: Eaton Страницы: 12

Бренд: I-Tork Страницы: 15

Бренд: Case IH Страницы: 81

Бренд: Rabbit Страницы: 12

Бренд: Renogy Страницы: 36

Бренд: BQT Страницы: 2

Бренд: Evco Страницы: 78

Бренд: Oilon Страницы: 74

Бренд: Harsen Страницы: 55

Бренд: Wabtec Страницы: 5

Touch Screen Controller EX112

Бренд: 3M Страницы: 40

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды