ADTRAN ATLAS 550 Скачать руководство пользователя страница 346

Страница: 346 / 412

Section 5 DLP-14

ATLAS 550 System Manual

346

61200305L2-1B

1. For the alarm relay contacts labeled

ALARM

, determine whether the external alarm reporting device

uses a normally open (NO) or normally closed (NC) circuit for alarm relay (see pinout in Table 1). The
ATLAS 550 external monitor labeled

RELAY MON

uses an NO circuit for alarm relay (see pinout in

Table 2).

2. Using standard telco cross-connect wire, determine and cut the length required to reach from the

alarm headers to the alarm-reporting device(s).

3. Using wire strippers, strip 1 inch from both ends of each wire.

4. If you want the ATLAS 550 to monitor for external alarms, remove both terminal blocks; otherwise, only

remove the 4-position terminal block (

ALARM

5. Using the small straight slot screwdriver, loosen the screws in the terminal block(s).

6. For the 4-position terminal block (

ALARM

), insert one strand into the third slot (counted from the left)

for the COM connection from the ATLAS 550.

7. Insert another strand into either the first slot or the second slot for the NC or NO connections,

respectively.

8. (Optional) If you wish to have the ATLAS 550 monitor for external alarms, insert one strand of wire into

the first slot (counted from the left) for the Alarm Out signal of the 2-position terminal block (

RELAY

Insert the other strand into the last slot for the Alarm In signal.

9. Connect the wires to the appropriate terminals on the external device(s) being used.

Perform the following steps below in the order listed:

Table 1. Alarm Relay Connector Pinout

Pin

Name

Description

Normally Closed (NC)

Opens when a selected alarm condition is present.

Normally Open (NO)

Closes when a selected alarm condition is present.

Common (COM)

Common connection between external circuitry and NC or NO terminal.

Chassis Ground (GND)

ALL EMPTY SLOTS MUST BE

COVERED WITH BLANK PANELS

500 Series

CAUTION: FOR CONTINUED PROTECTION

AGAINST RISK OF FIRE, REPLACE ONLY

WITH SAME TYPE AND RATING OF FUSE.

ETHERNET

ADMIN

RELAY

ALARM

MON

COM

500 Series

NETWORK 2

NETWORK 1

500 Series

FUSE RATING: 2A/250V SLO-BLO

90-240VAC, 2A 50/60Hz

Alarm Relay

Connection

External Alarm Relay

Monitor Connection

Содержание ATLAS 550





























































































































































































































































































































































































































Результаты поиска

Содержание ATLAS 550

Отзывы:

Похожие инструкции для ATLAS 550

Бренды по названию

Популярные бренды

ADTRAN ATLAS 550, Системное руководство

Результаты поиска

Содержание ATLAS 550

Отзывы:

Похожие инструкции для ATLAS 550

Бренды по названию

Популярные бренды