ADTRAN ATLAS 550 Скачать руководство пользователя страница 218

Страница: 218 / 412

Section 4 User Interface Guide

ATLAS 550 System Manual

218

61200305L2-1B

OUTER

> IP > ARP C

ACHE

> T

IME

Read security: 2

Displays the minutes since the entry was last referenced.

OUTER

> IP > ARP C

ACHE

> T

YPE

Read security: 2

Defines this entry as

YNAMIC

TATIC

OUTER

> IP > ARP C

ACHE

> I

NTERFACE

Read security: 2

Displays the interface upon which this entry was found.

OUTER

> IP > ARP C

ACHE

> T

ENDING

Read security: 2

Displays the number of transmit packets pending a reply.

OUTER

> IP > R

OUTES

Write security: 2; Read security: 2

The

OUTES

menu displays the contents of the ATLAS routing table. All static and discovered routes are

displayed from this menu.

OUTER

> IP > R

OUTES

> IP A

DDRESS

Read security: 2

Displays the IP address of the destination host or network.

OUTER

> IP > R

OUTES

> N

ETMASK

Read security: 2

Displays the subnet mask applied to the destination address.

OUTER

> IP > R

OUTES

> G

ATEWAY

Read security: 2

Displays the IP address of the next-hop router or host receiving the forwarded IP packet.

OUTER

> IP > R

OUTES

> I

NTERFACE

Read security: 2

Displays the next-hop router or host interface through which IP packets are routed, as defined here:

OCAL

Forwards the packet directly to the ATLAS router.

EN0 IP

Forwards the packet through the ATLAS Ethernet port.

NDPOINT

AME

Forwards the packet using the DLCI number.

Содержание ATLAS 550





























































































































































































































































































































































































































Результаты поиска

Содержание ATLAS 550

Отзывы:

Похожие инструкции для ATLAS 550

Бренды по названию

Популярные бренды

ADTRAN ATLAS 550, Системное руководство

Результаты поиска

Содержание ATLAS 550

Отзывы:

Похожие инструкции для ATLAS 550

Бренды по названию

Популярные бренды