background image

890 

Quickstart 

Manual 

 

AC890PX AC Drive 

 

 

 

HA471665U000 Issue 3 (ISO A4) 

HA471665U001 Issue 3 (American Quarto) 

 

 
 

©

 Copyright 2009 Parker Hannifin Ltd. 

All rights strictly reserved. No part of this document may be stored in a retrieval system, or transmitted in any 
form or by any means to persons not employed by a Parker Hannifin Ltd., Automation Group, SSD Drives 
Europe company without written permission from Parker Hannifin Ltd., Automation Group, SSD Drives Europe. 
Although every effort has been taken to ensure the accuracy of this document it may be necessary, without 
notice, to make amendments or correct omissions. Parker Hannifin Ltd., Automation Group, SSD Drives Europe 

cannot accept responsibility for damage, injury, or expenses resulting therefrom.

 

WARRANTY 

Parker SSD Drives warrants the goods against defects in design, materials and workmanship for the 

period of  24 months from the date of manufacture, 12 months from the date of delivery (whichever is the 

longer period) on the terms detailed in Parker SSD Drives Standard Conditions of Sale IA500504. 

 

Parker SSD Drives reserves the right to change the content and product specification without notice.

 

Содержание AC890PX Series



























Отзывы: