ADTRAN ATLAS 550 Скачать руководство пользователя страница 202

Страница: 202 / 412

Section 4 User Interface Guide

ATLAS 550 System Manual

202

61200305L2-1B

ACKUP

ODE

Write security: 3; Read security: 5

Provides switching options.

UTO

Provides normal operation.

ORCED

Forces a switch to backup.

ISABLED

Disables backup switching.

WITCH

UBLINK

NACTIVE

Write security: 3; Read security: 5

Provides switching options if the sublink goes down. Select

to switch to backup if the primary

sublink goes down, otherwise select

WITCH

LMI D

OWN

Write security: 3; Read security: 5

Provides switching options for LMI signaling. Select

to switch to backup if LMI signaling is

inactive on the primary link, otherwise select

WITCH

ACKUP

CTIVE

Write security: 3; Read security: 5

Provides switching options if the backup sublink goes active. Select

to switch to backup if the

backup sublink goes active, otherwise select

ACKUP

ELAY

ECONDS

Write security: 3; Read security: 5

The amount of time within which any of the enabled switch criteria must be met before service is
switched to the backup circuit.

ESTORE

ELAY

ECONDS

Write security: 3; Read security: 5

The amount of time within which the criteria for switching to backup are reached before service is
returned to the primary circuit.

Содержание ATLAS 550





























































































































































































































































































































































































































Результаты поиска

Содержание ATLAS 550

Отзывы:

Похожие инструкции для ATLAS 550

Бренды по названию

Популярные бренды

ADTRAN ATLAS 550, Системное руководство

Результаты поиска

Содержание ATLAS 550

Отзывы:

Похожие инструкции для ATLAS 550

Бренды по названию

Популярные бренды