ADTRAN ATLAS 550 Скачать руководство пользователя страница 158

Страница: 158 / 412

Section 4 User Interface Guide

ATLAS 550 System Manual

158

61200305L2-1B

ODULES

(E&M-8) > T

EST

> T

EST

Write security: 4; Read security: 5

Activates 2W (E&M) tests on a per-port basis. Options include

(no tests are active),

E-L

EAD

PEN

and

E-L

EAD

LOSED

. The 2W tests will disrupt the active call on the selected E&M port. Table 5 displays the

state of the 2W conductors during each test.

ODULES

(E&M-8) > T

EST

> TX ABCD

Write security: 4; Read security: 5

Forces the Transmit Robbed Bit Signaling (Tx RBS) to a specified value. Values include

, 0000, 0101,

1010,

1111

ODULES

(E&M-8) > T

EST

> 1

ONE

Write security: 3; Read security: 5

Sends a 1kHz tone into the following locations, based on test selection:

EAR

sends the tone out the E&M

VF port, while

sends the tone into the digital PCM stream of the ATLAS 550 controller. These tests

are useful for verifying a voice path.

ODULES

(E&M-8) > T

EST

> L

OOPBACK

Write security: 3; Read security: 5

Activates loopback tests on a per-port basis.

ODULES

(E&M-8) > C

ONFIG

Write security: 3; Read security: 5

All of the following configurable parameters apply to the individual E&M ports.

Table 5. E&M 2W State Table

EST

ODULE

UTPUT

Off

E-lead follows the Rx (received) signaling bits

E-Lead Open

Forces an on-hook situation on the port

E-Lead Closed

Forces an off-hook situation on the port

Calls may be affected when activating the Tx ABCD test. This test is not valid when the
port is used in the

IAL

LAN

Normal operation.

NALOG

Loops the 2W test on itself.

IGITAL

Loops digital data entering the E&M from the ATLAS controller on itself.

Loopback tests disrupt the call in progress on the selected E&M port.

Содержание ATLAS 550





























































































































































































































































































































































































































Результаты поиска

Содержание ATLAS 550

Отзывы:

Похожие инструкции для ATLAS 550

Бренды по названию

Популярные бренды

ADTRAN ATLAS 550, Системное руководство

Результаты поиска

Содержание ATLAS 550

Отзывы:

Похожие инструкции для ATLAS 550

Бренды по названию

Популярные бренды